I had manged to deploy and configure mesh networks on Nordic Thingy devices based on these 2 examples separately. 1. Generic OnOff models https://github.com/NordicPlayground...
Hello,
I am unable to access my SRJ profile with email id [email protected] due to two factor authentication. i do not get anything in the google authentication app...
The link for downloading nRF6939 live cd v5.4 is broken.
https://www.nordicsemi.com/Software-and-Tools/Reference-Designs/nRFready-Smart-Remote-3-for-nRF52-Series/Downlo...
Using one ADC, the current can be reduced to about 40uA after the ADC value is taken. Using a two-channel ADC, after the ADC value is taken, the current stops at about 0.4...
I'm searching for a software engineer who can help us getting OTA support between nRF52810 and PIC16 MCU.
nRF52810 must have command- and data mode over UART, Pic controler...
I want to be able to read the gyro and accelerometer values from the MPU6050 sensor.
As a base start I downloaded the NRF5 SDK V15.3.0 and modified twi_sensor_pca10056 program...
Hi
I am using nRF-SDK-Connect.
I downloaded SDK v1.5.1 through Toolchain in nRF Connect, and nRF5_SDK_17.0.2 (not through Toolchain).
What is the difference between...
Hello,
I want to capture 802.15.4 nRF packets with a python script using the pyshark library and an nRF52840 DK sniffer and an nRF52840 Dongle. the problem is that when...
Hi,
I've successfully integrated an out of tree driver using the out_of_tree_driver example in the application_development sample folder for Zephyr; it has built and ran...
Hello,
given that the Micro:bit V2 (Nrf52833 based) has been promoted in Webinars, I am surprised on the lack of enthousiasm in getting it to work properly under NCS/Zephyr...
Hi
I checked how AT%XOPNAME could be used to receive notifications about operator name updates. However I'm wondering about the notification syntax.
According to the specification...
https://infocenter.nordicsemi.com/index.jsp?topic=%2Fcom.nordic.infocenter.meshsdk.v5.0.0%2Fmd_examples_sdk_coexist_ble_app_uart_coexist_README.html&cp=8_2_3_3_1
In this...
Hi,
I developed some multi peripheral units. and also i developed some central units which are allowed to connect to the multi peripheral devices.
F.E: i got 2 multi peripheral...
dear all
I use nrf52840 to compile a library with floating-point operation. I configured it in my *. Conf
CONFIG_ FPU = y, but we can't find sqrtf, sinf, logf and so on...
For a customer I am developing a Zigbee coordinator / Gateway with the nRF52840. As software basis I use the “Zigbee cli example” from SDK V4.1.0.
So far, everything works...
I installed nRF Connect SDK v1.6.0 and SES Nordic Edition through the nRF Connect toolchain manager (Windows 10). I'm finding that I can't use the "open nRF Connect SDK Project...
Hello,
I'm trying to make the RF frequency of TX channel configurable.
I have noticed that anything higher than 0x50 is not acceptable for sd_ant_channel_radio_freq_set...
Hi,
I wanted to use the console on nRF52840DK in high-speed UART mode (921600bps) but it fails and I just saw the DK User Manual says:
Baud rate 921 600 is not supported...
I'm using the ble_nus_c NUS client code for a custom 1:1 data link between two embedded nodes, just pinging a few bytes of data back and forth every 3 seconds. Bonded connection...
Hi,
We are using nRF52840 SOC with our custom board . Due to some reason, the SWD data line( SWDIO pin ) shorted .
So now we are looking into how we can program nRF52840...
