I'm searching for a software engineer who can help us getting OTA support between nRF52810 and PIC16 MCU.
nRF52810 must have command- and data mode over UART, Pic controler...
I want to be able to read the gyro and accelerometer values from the MPU6050 sensor.
As a base start I downloaded the NRF5 SDK V15.3.0 and modified twi_sensor_pca10056 program...
Hi. I'm using nRF52832, SDK13.0.0.
I should use SHA256 and MD5.
I made my code as below.
NRF_CRYPTO_HASH_CREATE(init_packet_hash, SHA256); NRF_CRYPTO_HASH_CREATE(init_packet_md5...
Hi. I'm using nRF52832, SDK13.0.0.
I want to use SHA256 as below.
output32Byte = SHA256[input32Byte];
Which function or example can I refer to?
And also I want to...
I tried to port the example "ble_app_ipsp_initiator" to pc-ble-driver and run on Linux. The peer device is another PCA10056 device running ble_app_ipsp_acceptor. The problem...
hi...
i want to use two uarts in nRF52840 , one uart to one pc and another uart to another pc .Data should be transferred and received between the nRF52840 and pc how can...
Hi, i'm using two nrf52840 DK ev kit. One it's the central and one the peripheral
After the connection I need to save power at the peripheral board, because the cpnsumptio...
Hi,
I want to verify
1. Program ble_app_hrs with buttonless dfu integrated + secure bootloader + bootloader setting to nRF52DK.
2. Boot up nRF52DK, then use buttonless...
I don't know what happened to my thingy 52 after lots of firmware updates with Keil+Jlink+thingysdkv210 and nRF connect operations. The LED on thingy isn't flashing any more...
Hi engineers,
I want to use saadc to measure the battery's voltage, but the result I get is incorrect.
So I use the saadc demo of the nrf5_sdk17, then I measure GND(negative...
Hi. I am trying to use PIN 0.19 as my SPI CLK but it is always low.
Previously, I tried to change the pin to 0.26 and it works.
Is there any other configuration required...
Hi Nordic
SInce this is my first time to develop Nordic chip and implement SPIS driver, Therefore i am not so familiar with Nordic API. I would really appreciate it if...
HI,
I want to upgrade the BL in APP directly. I encouter a wierd problem. When APP erase a specific page of the BL(the address is 0x74000), the system halts. If ignoring...
Hello,
I am using nrf51822/SDK 12.3/sd 130.
An error occurred while implementing nus_c using multi-role example.
Error 7 occurs in sd_ble_gap_conn_param_update() frequently...
Hi,
I used Jlink Edu successfully to flash the asset tracker code using segger. but when put the breakpoint it went to some different file.
I have a quick question regarding...
I have just received an nRF52833-DK and am trying to get started with it.
I am at the website:
https://www.nordicsemi.com/Software-and-tools/Development-Kits/nRF52833...
Hi,
I press Button 1 and Reset to put the nRF52840 DK in to DFU mode that is programmed with a immutable bootloader (B0), mcuboot, and application. This works well to...
Hey. I am new to this forum and new to programming BLE chips. I have ordered my first dev board and cant wait to get my hands on it. I have been reading a lot for the coupe...
Guys,
I am currently experimenting with an existing wearable that contains an NRF52832XXAA Revision 1, and I'm having a hard time to have it running a simple BLE peripheral...
Hey everyone! My team and I are working on making a hex file that contains the soft device and software, as found in the 15.3.0 SDK, in the secure dfu test images folder....
I'm wondering about a scenario where an attacker has physical access, and manages to program their custom application into our device. They could use our stored credentials...
