I had manged to deploy and configure mesh networks on Nordic Thingy devices based on these 2 examples separately. 1. Generic OnOff models https://github.com/NordicPlayground...
Hello,
I am unable to access my SRJ profile with email id [email protected] due to two factor authentication. i do not get anything in the google authentication app...
The link for downloading nRF6939 live cd v5.4 is broken.
https://www.nordicsemi.com/Software-and-Tools/Reference-Designs/nRFready-Smart-Remote-3-for-nRF52-Series/Downlo...
Using one ADC, the current can be reduced to about 40uA after the ADC value is taken. Using a two-channel ADC, after the ADC value is taken, the current stops at about 0.4...
I'm searching for a software engineer who can help us getting OTA support between nRF52810 and PIC16 MCU.
nRF52810 must have command- and data mode over UART, Pic controler...
I want to be able to read the gyro and accelerometer values from the MPU6050 sensor.
As a base start I downloaded the NRF5 SDK V15.3.0 and modified twi_sensor_pca10056 program...
I'm trying to get a gas gauge and charger IC to work on the i2c bus. Both have different addresses. I'm able to read from the gas gauge address but not the IC. Are there specific...
Hi Nordic:
I use NRF54L15 for my product and hope to use ANT+AND BLE. Does NCS2.8 currently support it?
I couldn't find a example program for ANT+in NCS2.8. How can I...
Hello support team,
I am developing a mobile app to communicate on BLE coded phy (long range) with nrf5340DK. The nrf connect for mobile on android works fine, but not ios...
We have some devices that run the same firmware, but need different default BLE tx power settings.
There is a KConfig value to set the default, but in our case it is different...
Hello,
I am going through the intermediate DevAcademy tutorials right now because I specifically need to use the 52840 dev kit to interface with a SPI driven ili9340 device...
Hi everyone,
Edit: Consider that I'm on ncs 2.6.1
What are the current methods for provisioning an nRF9160 on the nRF Cloud? I have an ongoing project with the nRF9160...
This sample can be found under samples/nrf_compress/mcuboot_update in the nRF Connect SDK folder structure.I want to know the whole decompression process,I added a lot of...
Hi,
I am building an app that connects to the NRF52840 with BLE. The NRF board is attached to an electrocardiogram(ECG) setup, so I am interested in the app being able to...
Hello,
I am using the hci_usb sample from Zephyr and running BlueZ 5.53 on Ubuntu 20.04. I am trying to increase the ACL packet size from the default value of 27 bytes and...
Hi,
I am using SDK v2.6.1.
Is there any course available on DevAcademy for WebSockets?
For WebSocket i take reference of v2.6.1/zephyr/samples/net/sockets/websocket_client...
Hello there,
I am using nrf connect sdk using vs code.
Toolchain: v2.7.0 SDK: v2.7.0
I have custom hardware board based on nrf52811 SoC.
I have completed a firmware...
Hi
We have a project previously built on NCS v2.6.0 and now we need to migrate it to v2.8.0
I see from v2.9.0 child/parent build setup is not supported and so we are planning...
I'm using ”ncs\v2.8.0\nrf\samples\nrf_compress\mcuboot_update“ this routine.After connecting the Bluetooth, put in the DFU package (mcuboot_update\build\dfu_application.zip...
Hi,
We are trying to enable oversampling in an application that is based on your DF connectionless RX sample, build with Zephyr version 3.4.99.
Something similar was asked...
Hi,
I've a good experience with nRF5340 pre-certified modules and nRF Connect SDK. I'm evaluating leveraging Nordic Thingy:91 X platform to build a new product. However...
