The link for downloading nRF6939 live cd v5.4 is broken.
https://www.nordicsemi.com/Software-and-Tools/Reference-Designs/nRFready-Smart-Remote-3-for-nRF52-Series/Downlo...
Using one ADC, the current can be reduced to about 40uA after the ADC value is taken. Using a two-channel ADC, after the ADC value is taken, the current stops at about 0.4...
I'm searching for a software engineer who can help us getting OTA support between nRF52810 and PIC16 MCU.
nRF52810 must have command- and data mode over UART, Pic controler...
I want to be able to read the gyro and accelerometer values from the MPU6050 sensor.
As a base start I downloaded the NRF5 SDK V15.3.0 and modified twi_sensor_pca10056 program...
Hi. I'm using nRF52832, SDK13.0.0.
I should use SHA256 and MD5.
I made my code as below.
NRF_CRYPTO_HASH_CREATE(init_packet_hash, SHA256); NRF_CRYPTO_HASH_CREATE(init_packet_md5...
Hi. I'm using nRF52832, SDK13.0.0.
I want to use SHA256 as below.
output32Byte = SHA256[input32Byte];
Which function or example can I refer to?
And also I want to...
I tried to port the example "ble_app_ipsp_initiator" to pc-ble-driver and run on Linux. The peer device is another PCA10056 device running ble_app_ipsp_acceptor. The problem...
I work for nRF52833 on NCS2.8.0.
I try to set SB_CONFIG_MCUBOOT_COMPRESSED_IMAGE_SUPPORT=y for sysbuild.
build error is occured.
Maybe there is not enough RAM for mcuboot...
My NCS version is 2.6.1, and the modem firmware version is 1.3.6
I found that delta upgrade often fails when testing the firmware of FOTA upgrade modem for 9160. Currently...
Hello. How can I monitor that SoftDevice is working properly? I am trying to monitor using Radio notification, but RADIO Active does not guarantee that the SoftDevice is working...
Hi ,
I am running "Cellular IoT Fundamentals". In Lesson 4, Exercise 1, has MQTT communication. Everything went well up to the point where I have to PUBLISH from MQTT Explorer...
Hello,
I'm new to pretty much all of this, but I'll do my best to explain my issue. As the title says, I'm currently trying to get a LSM6DSO sensor to work with the NRF52832...
Is there a way to avoid duplicate board targets if I have the same repository in two different places on my machine?
Or some way to ignore a workspace path so they're...
I am working on a project using ncs 2.2.0 on the nRF52833DK.
I have a very simple requirement, which is to save an id-data pair in Non-Volatile Storage and be able to change...
I made an example based on the NVS sample code (Connect SDK 2.2.0) which simply reads a value from the storage partition if it exists, then updates it if either it's different...
We have a system with a central device and a peripheral both based on nrf5340. The central device is also a Broadcast source and the peripheral is also a Broadcast sink in...
I’m working with the Audio Application (from the Nordic sample program) on an nRF5340 Audio DK as a gateway, and a custom board with an nRF5340 as a headset. The custom headset...
Hi, I'm running the fatfs sample using an Actinius Icarus board (nrf9160) and a microSD card, connected via SPI. The original sample works as it should (it mounts and opens...
Before setting `CONFIG_USERSPACE=y`, my image size is ~680KB. After setting it, it overflows my partition by ~60KB. The partition size is ~840KB, meaning userspace has added...
Hi,
I am testing the BLE beacon sample on the NRF54L15 PDK, and it was successful as I was able to detect the beacon using the NRF Connect scanner. However, when monitoring...
I am developing the LE Audio feature for nrf5340. My project is based on nrf5340_audio demo, base on NCS 2.7.0. I am not very familiar with sysbuild. In NCS2.4.0, I am able...
