Using one ADC, the current can be reduced to about 40uA after the ADC value is taken. Using a two-channel ADC, after the ADC value is taken, the current stops at about 0.4...
I'm searching for a software engineer who can help us getting OTA support between nRF52810 and PIC16 MCU.
nRF52810 must have command- and data mode over UART, Pic controler...
I want to be able to read the gyro and accelerometer values from the MPU6050 sensor.
As a base start I downloaded the NRF5 SDK V15.3.0 and modified twi_sensor_pca10056 program...
Hi. I'm using nRF52832, SDK13.0.0.
I should use SHA256 and MD5.
I made my code as below.
NRF_CRYPTO_HASH_CREATE(init_packet_hash, SHA256); NRF_CRYPTO_HASH_CREATE(init_packet_md5...
Hi. I'm using nRF52832, SDK13.0.0.
I want to use SHA256 as below.
output32Byte = SHA256[input32Byte];
Which function or example can I refer to?
And also I want to...
I tried to port the example "ble_app_ipsp_initiator" to pc-ble-driver and run on Linux. The peer device is another PCA10056 device running ble_app_ipsp_acceptor. The problem...
hi...
i want to use two uarts in nRF52840 , one uart to one pc and another uart to another pc .Data should be transferred and received between the nRF52840 and pc how can...
Hi,
we are developing a custom board based on nrf9160 that include CAN bus. When updating nRF Connect SDK from v1.4.2 to v1.5.0 we can not get CAN-bus up and running again...
Hello,
For our device we are using a NRF52832 and SDK version 17.0.2. It only has one Button connected to P02. Due to needing the device to be water resistant the decision...
I built the mouse BLE example .
In Windows 10 "Add a device" detects the Nordic_HIDS_mouse device and then issues the
challenge Press Connect if the PIN on Nordic_HIDS_Mouse...
Hi Everybody,
I am working on USBD keyboard.
I used USBD example for implementation.
I changed mouse profile to keyboard profile.
And it's recognized well without...
Is there a way to get the signals of the interrupt for a push-button/interrupt from the pin_change_int example in a logic analyzer software tool? Basically i'd want to visualize...
In bluetooth mesh only 3 channel are used.There is a way to use mesh with an extended number of channel.
Because in some industrial enviroments fading is very heavy and...
I was reviewing the silicon errata for Rev2 of the Nrf52840 and I found this.
[204] RADIO: Switching between TX and RX causes unwanted emissions
This anomaly applies...
I have a smart watch based on nrf51822.but i don't have the customer app.I download the nrf tool box can read the heart rate.But i don't know how to set or sync time,can someone...
Hi,
I have developed an app using OTA DFU support. Soft device used is S112.
is it possible to update Soft device through OTA DFU?
what is the max size of the image...
Hi , How can I connect arduino nano 33 ble with the application NRF Toolbox using Bleutooth when I program the arduino with segger embeded studio .
Please I need your help...
Hello:
After the nrf52 lost connection with the phone, should it go to the Directed mode of just start normal fast advertising. And what the differences between them?
...
Hi,
I just used the nRF Connect Toolchain manager to install the NRF Connect SDK. Then, the Segger studio keeps popping this error when I try to open a project:
And...
Hello,
From the nrf91dk datasheet, a stackup is provided. Because it looks custom, and I'm having a hard time finding a manufacturer that can do that stackup. What PCB...
hi，
I read the data manual of 52832, but I have some questions about the following parameters, like CM_FLASH,CM_FLASH/MHZ,CM_FLASH/MA,please explain it in detail and what...
