Hi,
I find the CSCS example program reading zero at low cadence levels below around 50 rpm.
Using ble_peripheral example ble_app_cscs loaded into the PCA10040 board or...
I had manged to deploy and configure mesh networks on Nordic Thingy devices based on these 2 examples separately. 1. Generic OnOff models https://github.com/NordicPlayground...
Hello,
I am unable to access my SRJ profile with email id [email protected] due to two factor authentication. i do not get anything in the google authentication app...
The link for downloading nRF6939 live cd v5.4 is broken.
https://www.nordicsemi.com/Software-and-Tools/Reference-Designs/nRFready-Smart-Remote-3-for-nRF52-Series/Downlo...
Using one ADC, the current can be reduced to about 40uA after the ADC value is taken. Using a two-channel ADC, after the ADC value is taken, the current stops at about 0.4...
I'm searching for a software engineer who can help us getting OTA support between nRF52810 and PIC16 MCU.
nRF52810 must have command- and data mode over UART, Pic controler...
Hello,
I was downloading a project to the flash memory using J-Link SDK and I am having this messsage:
JLink info: ------------ DLL: V6.80a, compiled May 29 2020 16:27...
Hi,
I tried connecting the thingy91 out of the box and it was working fine, sending data to nrfCloud.
Now I tried to build the asset tracker application on my own and...
Hi All,
I am facing the issue with sleep current in nrf51822. initially i checked the sleep current 11uA. but after one hour it is increasing to up to 390 uA gradually....
Hi All,
I am currently designing a BLE module using nRF52840 chip which works with battery.
In the nRF52840 DK, it uses a Power Switch Driver ( SC728CSTRT ) from Semtech...
I want to add a button function to the ble_app_uart.
I don't need to use the functions of the BLE Button Module.
It's enough to just change the value of the variable when...
Hello,
I'm trying to develop a small module based around the nrf52832 chip, and I am trying to replicate the reference design and layout as closely as possible. One problem...
Hello,
I am updating my application from older SDK 15.0 to use SDK 17.0.
NRFX_NFCT_ENABLED NRFX_CLOCK_ENABLED are used to enable the files nrfx_nfct.c, nrfx_clock.c respectively...
Hello DevZone,
I am developing a system that has a SoftDevice, UART bootloader, and application. The SoftDevice is S132 SoftDevice v6.1.1. The UART bootloader and application...
RTT seems to be mostly working using the viewer with the command:
JLinkRTTViewer -device nRF52840_xxAA
It seems I need to re-connect each time I start a debug from SES...
Hello Nordic
We are in the process of product development and at the moment we need a chip that transmits stereo audio to any BT headset. That it is possible to control...
I am using nRF52840 as a master to communicate with esp32. For esp32 i am using arduino ide and esp 32 slave library( available in library manager of arduino ide).
For nRF52840...
Hello,
I use nrf52832 with 65 kb RAM.
I can't understand why soft device takes about 30k RAM memory.
I see "reserved_ram" has 30k.
Can I change size for 20k for...
We're using the nRF52840 on a battery-powered device that requires very low power consumption, both in run mode and also in the Cortex-M4 sleep / deep sleep modes. We've recently...
Hi, I'm trying to enable the entropy driver so that sys_csrand_get() will stop returning "Entropy reseed error". Does anyone know why it's grayed out? I have tried enabling...
