Using one ADC, the current can be reduced to about 40uA after the ADC value is taken. Using a two-channel ADC, after the ADC value is taken, the current stops at about 0.4...
I'm searching for a software engineer who can help us getting OTA support between nRF52810 and PIC16 MCU.
nRF52810 must have command- and data mode over UART, Pic controler...
I want to be able to read the gyro and accelerometer values from the MPU6050 sensor.
As a base start I downloaded the NRF5 SDK V15.3.0 and modified twi_sensor_pca10056 program...
Hi. I'm using nRF52832, SDK13.0.0.
I should use SHA256 and MD5.
I made my code as below.
NRF_CRYPTO_HASH_CREATE(init_packet_hash, SHA256); NRF_CRYPTO_HASH_CREATE(init_packet_md5...
Hi. I'm using nRF52832, SDK13.0.0.
I want to use SHA256 as below.
output32Byte = SHA256[input32Byte];
Which function or example can I refer to?
And also I want to...
I tried to port the example "ble_app_ipsp_initiator" to pc-ble-driver and run on Linux. The peer device is another PCA10056 device running ble_app_ipsp_acceptor. The problem...
hi...
i want to use two uarts in nRF52840 , one uart to one pc and another uart to another pc .Data should be transferred and received between the nRF52840 and pc how can...
I have a question regarding Direction Finding on nRF52833. I cant see any examples related to this in new SDK 16, also I cant see any antenna array recommendation. Do you...
When building a project I get a number of undefined symbols:
.\_build\nrf52840_xxaa.axf: Error: L6218E: Undefined symbol __start_fs_data (referred from nrf_fstorage.o)....
Hi,
I am planning to design a custom board using nrf52840 Soc which receive analog signal from sensor and send ADC outputs through UART to smartphones using Bluetooth communication...
Hi, Everyone
I use sdk15.2 & nrf52832
I am doing a test to read the slave address in TWI
There is one slave device on the board and the slave address is 0x68
I used three...
I am working with SPIS example ( sdk version 15.3). SPI master send data regulaly. For example, it sent 5ms cs low, but there are only two bytes transferred, the first byte...
Hi,
I'm working on a project that is using the the freeRTOS and I want to use the NFC pins P0.9 P0.10 to drive SOFTWARE SERIAL UART with a timer like TIMER1, when I try...
iPhone 8 Plus with nRF connect App[iOS], does not shows BLE 5 beacon in scanning, it only scanning BLE 4 beacons, In Spec of phone it shows it support BLE 5
nRF connect...
Hello,
I follow the nRF Connect SDK on a Windows 10 x64 computer and it's a crap. I get a lot of errors like this one. It's so crappy that I doubt that I will continue with...
Hello,
I am not able to send a command from the BLE (52810) to a DSP over UART which are on my custom board. I have modified a program that uses UART for logging purpose...
The s132_nrf52_7.0.1 documentation says: Call stack: The SoftDevice uses a call stack combined with the application. The worst-case stack usage for the SoftDevic e is 1.5...
I am doing a program based on Current Time Application example. But I have a few questions, so I hope you can help me. First, I am using Battery service together. By the way...
Hi,
In our current project we use nordic NRF52832 ble to send some data(~200 Byte / packet) to host, we expect each transmission to be done within 10ms, but results from...
Hello. nRF52 A custom board is being developed. I want to use Crypto Chip Pulse to encrypt. Pulse_Out of Crypto Chip is connected to P028/AIN4. In order to measure Pulse,...
I'm using \nRF5_SDK_15.3.0_xxxxx\examples\peripheral\usbd_ble_uart example to use two communication links. Missing echo on the USB virtual COM is a small frustration. I've...
