I tried to port the example "ble_app_ipsp_initiator" to pc-ble-driver and run on Linux. The peer device is another PCA10056 device running ble_app_ipsp_acceptor. The problem...
hi...
i want to use two uarts in nRF52840 , one uart to one pc and another uart to another pc .Data should be transferred and received between the nRF52840 and pc how can...
Hi, i'm using two nrf52840 DK ev kit. One it's the central and one the peripheral
After the connection I need to save power at the peripheral board, because the cpnsumptio...
In mesh example project “dimming_server”，I have added functions: mesh serial, SAADC(use ppi) and compie pass.However,when debugging,an error is happened in the function"nrf_drv_timer_init...
NRF52840 support the long range bluetooth and BLE gateway SDK, look at here that RAK Wireless held a Beta and welcome the community to participate.This board with Cellular...
Good day!
Started to work with nRF mesh. And wanted to add ir_lib from this project to Generic OnOff example.
And Source navigator shows error: static_assert failed "unspecified...
You have dead links everywhere and no obvious location for the gcc command line tools. Where is this?
Here are dead links:
https://infocenter.nordicsemi.com/index.jsp...
Hi Nordic team, We have a project that uses nRF5340 &NCS 2.7.0, and we encountered net core crashing issue each time when ble is connected by central device and 5340 app core...
Description:
Hello,
I am trying to build my project nrf_dm_testing using NCS 2.9.0 , but I am encountering a CMake configuration error. The error message is as follows...
I am using 9160 as slave which communicates with nrf5340(master) over UART. with flow control disabled everything works but as soon as I enable the hardware flow control then...
Hello,
I have a few questions regarding the nPM1300 current measurements:
As far as I understand, there are two ways to trigger a current measurement:
By writing...
I am using VS Code IDE and have installed nrf Connect Extension and done with the installation part and blinky and few other samples. So, basically I just copied an available...
I have figured out a way to realize IR communication,it is same with the way to drive WS2812 with SPI.
[ I can use PWM peripheral and should use it,for I need to change...
Just to confirm the head question.
I have found the same question : NRF52 help configuring TIMER + DMA + PWM - Nordic Q&A - Nordic DevZone - Nordic DevZone
There is no...
Hello,
1. Do you have any hardware to implement Wireless HID USB without Bluetooth like Logitech with USB dongle?
2. Do you have an example of IR TV remote for any hardware...
Hello,
NCS 2.9.0 nRF54L15 DK 0.9.1
I am trying to follow the instructions in the manual in the User Guide of the nRF54L15 DK to use P1.00 and P1.01 as normal GPIOs. (side...
Hello,
I have been following the steps in Exercise 1 of Lesson 1 of the Cellular IoT Fundamentals course. I have a Thingy:91. I have followed the steps so far
- flashed...
Hi
Long time no see
I recently got my sweaty hands on a sparkly new 54L15DK, and I thought I would try it out. The AI guided me to the coremark sample and the multicore...
I recently tired the Onomondo static and external softSim demo on the nRF9151 DK. For both of the demos they take around 4 minutes until the DK gets a cellular connection...
What is the connector cable that fits with nRF5340 DK J1, I am using the other end to connect to the ANT-B10 J2 (antenna board). I will like to know which connector cable...
I am currently trying to add MCU boot to my application using sysbuild. I have done the following :
Created sysbuild.conf in application root
Created sysbuild folder...
