I'm searching for a software engineer who can help us getting OTA support between nRF52810 and PIC16 MCU.
nRF52810 must have command- and data mode over UART, Pic controler...
I want to be able to read the gyro and accelerometer values from the MPU6050 sensor.
As a base start I downloaded the NRF5 SDK V15.3.0 and modified twi_sensor_pca10056 program...
Hi. I'm using nRF52832, SDK13.0.0.
I should use SHA256 and MD5.
I made my code as below.
NRF_CRYPTO_HASH_CREATE(init_packet_hash, SHA256); NRF_CRYPTO_HASH_CREATE(init_packet_md5...
Hi. I'm using nRF52832, SDK13.0.0.
I want to use SHA256 as below.
output32Byte = SHA256[input32Byte];
Which function or example can I refer to?
And also I want to...
I tried to port the example "ble_app_ipsp_initiator" to pc-ble-driver and run on Linux. The peer device is another PCA10056 device running ble_app_ipsp_acceptor. The problem...
hi...
i want to use two uarts in nRF52840 , one uart to one pc and another uart to another pc .Data should be transferred and received between the nRF52840 and pc how can...
Hi, i'm using two nrf52840 DK ev kit. One it's the central and one the peripheral
After the connection I need to save power at the peripheral board, because the cpnsumptio...
Hi, i am working with usb cdc driver (sdk 15.3 and nrf52840) and i have a problem . This is my variables initialization APP_USBD_CDC_ACM_GLOBAL_DEF(m_app_cdc_acm, cdc_acm_user_ev_handler...
Hello,
I send SMS from nRF9160 to my number using following method.
1. Open LTE Socket
2. Send AT Commands:
a. AT+ CFUN?
b. AT + CFUN = 1
c. AT+ CFUN?
d. AT...
Hi all, If using the RC LF instead of a 32.768KHz crystal are there any side effects of the 16ms calibration period which occurs every 4 seconds? I'm mostly concerned how...
Hi,
I am working on buttonless dfu example, but i want to design my application in such a way that, device should enter into dfu mode when button is pressed. I should be...
Hi, I have some issue about mesh network.
Using below developing environment.
- SEGGER Embedded studio for ARM V4.22
- nRF SDK 15.3.0
- nRF Mesh SDK 3.2.0
- chip...
Hello
I'm a beginner in Bluetooh and I bought two dev board NRF52840 DK. I would like to make a mesh with these two boards. One in master and the other in relay, the goal...
Hi,
I´m working with "TWI Sensor" example of SDK 16 and I modified the Main function of main.c as follows (just added NRF_LOG_INFO("\r\ntest") );:
I just added this...
Is there a good way to uniquely identify mesh node across multiple smart phones? The problem is: Android provides access to MAC addresses that can be used as identifiers of...
Hello. When I examined the BLE data format, I found that it was as shown in Figure 1.
Fig1
I am using NRF52832, please tell me how to detect the CRC value...
I am using mbedtls with ECB hard accelerator on nRF52840. So I changed the macro definition: UPDATE_CBC_MAC in ccm.c to function:
#define HT_UPDATE_CBC_MAC \
for ( i...
Hi All,
we're developing beacon that advertise both legacy and long range at the same time.
however we got NO_MEM error while adding 2nd adv set
any limit on multiple...
Hello,
I am working with the Interactive PyACI (nRF_SDK_for_Mesh 4.0.0 with boards nRF52832). I followed the tutorial "demo_configuration" present in the doc folder. Every...
Hi,
I am trying to test the radio example from Eclipse. So i took one of my projects on SDK15.2 that works with the NRF52832, I cloned it and renamed it.
The arborescence...
Hello,
I'm using Thingy:52 to monitor FSR sensors in addition to MPU data.
I use saadc and can measure up to 8 FSR sensors thanks a multiplexer, it take about 10 ms for...
