Using one ADC, the current can be reduced to about 40uA after the ADC value is taken. Using a two-channel ADC, after the ADC value is taken, the current stops at about 0.4...
I'm searching for a software engineer who can help us getting OTA support between nRF52810 and PIC16 MCU.
nRF52810 must have command- and data mode over UART, Pic controler...
I want to be able to read the gyro and accelerometer values from the MPU6050 sensor.
As a base start I downloaded the NRF5 SDK V15.3.0 and modified twi_sensor_pca10056 program...
Hi. I'm using nRF52832, SDK13.0.0.
I should use SHA256 and MD5.
I made my code as below.
NRF_CRYPTO_HASH_CREATE(init_packet_hash, SHA256); NRF_CRYPTO_HASH_CREATE(init_packet_md5...
Hi. I'm using nRF52832, SDK13.0.0.
I want to use SHA256 as below.
output32Byte = SHA256[input32Byte];
Which function or example can I refer to?
And also I want to...
I tried to port the example "ble_app_ipsp_initiator" to pc-ble-driver and run on Linux. The peer device is another PCA10056 device running ble_app_ipsp_acceptor. The problem...
hi...
i want to use two uarts in nRF52840 , one uart to one pc and another uart to another pc .Data should be transferred and received between the nRF52840 and pc how can...
I have a question about what functionality is handled in the modem firmware vs. the application firmware.
I see from the nRF Connect SDK that the nRF9160 application communicates...
I'm using segger IDE for EVK-NINA-B1. I've downloaded nRF5_SDK_16.0.0 and trying yo run one of its example but getting error like stray '#' in program. I've attached 2 pictures...
Hi,
I'm using NRF52832 SDK15.2 to develop a smart band. Each time reconnect with iphone, the application assert in the peer manager event handler pm_evt_handler().
Any...
Hi Team,
I would like to know what does the system do after I call system off function as per below:
I have check through the oscilloscope to check how's the system...
Hi Team,
I am in the UK and trying to get an evaluation sim from Vodafone for NB-IoT. However they have set a limit of 2 IP addresses and hence I need the IP address of...
I'm developing bluetooth logging software on the nRF51 DK using SDK 12.3.0. We had been developing for some time in mbed, but were advised to switch over to Keil using the...
Hi,
I'm working on sending reliable message from server to client, the models are modified from RSSI model.
When I tring to send messages to client it will keep sending...
I've been trying to store an array (SDK16,S332)
uint8_t my_data[]={0x00,0x01,0x02,0x03,0x04,0x05,0x06,.........0x23}
using fstorage I wrote an update function :
I hardcoded...
To the kind attention of Nordic support team,
I'm trying to do things like in https://devzone.nordicsemi.com/f/nordic-q-a/39630/windows-command-line-dfu-over-ble-with-pca10059...
Hi,
I have a project which was originally written using SDK12, and have updated it to SDK16, I am sorry I know this question seems to have been asked in many different ways...
Dear,
Like I said in the title, I did use the NFC of my PCA10056 with my phone, it works, I also can read some information from nRF52840 by NFC. Right now, I programmed...
Hi Devzone:
I am working on nRF52840 with latest SDK.
I have 1 differential pair and 1 single ended pin I want to sample, single ended samples at every 40ms while differential...
I was trying to connect my cellphone tu the ublox modulo for sends at commands from my cell, in the main program of the micro I've the next lines for turn on the ublox module...
i have a nrf52840 dk
i need to connect the flex sensor to the board and know the resistance value while bending
how to do it?
and what code should i dump
Hi there,
I have developed the custom board with nrf52832 Soc and programmed blink code, it works fine.Now i uploaded the ble DFU template example and updated firmware...
