Using one ADC, the current can be reduced to about 40uA after the ADC value is taken. Using a two-channel ADC, after the ADC value is taken, the current stops at about 0.4...
I'm searching for a software engineer who can help us getting OTA support between nRF52810 and PIC16 MCU.
nRF52810 must have command- and data mode over UART, Pic controler...
I want to be able to read the gyro and accelerometer values from the MPU6050 sensor.
As a base start I downloaded the NRF5 SDK V15.3.0 and modified twi_sensor_pca10056 program...
Hi. I'm using nRF52832, SDK13.0.0.
I should use SHA256 and MD5.
I made my code as below.
NRF_CRYPTO_HASH_CREATE(init_packet_hash, SHA256); NRF_CRYPTO_HASH_CREATE(init_packet_md5...
Hi. I'm using nRF52832, SDK13.0.0.
I want to use SHA256 as below.
output32Byte = SHA256[input32Byte];
Which function or example can I refer to?
And also I want to...
I tried to port the example "ble_app_ipsp_initiator" to pc-ble-driver and run on Linux. The peer device is another PCA10056 device running ble_app_ipsp_acceptor. The problem...
hi...
i want to use two uarts in nRF52840 , one uart to one pc and another uart to another pc .Data should be transferred and received between the nRF52840 and pc how can...
Hi, I'm migraing our project to the latest NRF5 SDK v15.0.0 (S132 v6.0.0). We were previously on v12.2.0 (S132 v3.0.0) using the BLE DFU Bootloader. I've modified our bootloader...
Hello.
I try to modify ligh_switch_demo to switch state of 4 servers. I prepared 4 custom boards (server), one client and one provisioner. Provisioning was successful. I...
Dear All,
I am using "Scheduler" module as mentioned in this tutorial Scheduler Tutorial .
I have one question. My scheduler tasks are using some SD functions which require...
Hi!
This is a general question about the Bluetooth Mesh standard and a request for some hints to your implementation.
Scenario: Say you have a remote control device...
Hi
I'm really excited about Bluetooth 5 and Mesh Networking, but I'm not sure what DK to get.
I want to make Sensor Network for Building Automation. So I can read every...
I'd like to add some application-specific data for each peer that the Peer Manager handles. I've looked at pm_peer_data_app_store(), which uses pm_peer_data_store(). However...
Hi
As title, many customers interested in Zigbee protocol complained SDK Zigbee had not supported KEIL or SES but IAR.
It will cause their R&D loading for using multi...
Dear all:
I would like to add the health model to PyACI (`interactive_pyaci.py`),from the SDK 2.0.1 we can know that there is two model in the script:
1. config.py
2...
Does any of smartphone chips supported Bluetooth 5 long range (coded phy) nowadays. For example snapdragon 630, 660, 835, 845 or mediatecs. If it does, how can you understand...
Hey guys,
I'm trying to use the ADC device driver in SDK 15 (saadc seems to always use an event handler and thus require interrupts, right?). It won't compile since there...
I am using sdk which is mesh 1.0.1
How to detect the number of nodes in the mesh network, just like adding or missing？
The light_swtich example The values of m_provisioned_devices...
I'm trying to setup a basic program for my NRF52DK to send SAADC values on pin0 of the board over Bluetooth to the nordic android app by updating characteristic values. I...
Hi
In the serial secure bootloader example (SDK 13.0), RAM region end address is defined as:
define symbol __ICFEDIT_region_RAM_end__ = 0x2000ff7f;
What are the last...
