I'm searching for a software engineer who can help us getting OTA support between nRF52810 and PIC16 MCU.
nRF52810 must have command- and data mode over UART, Pic controler...
I want to be able to read the gyro and accelerometer values from the MPU6050 sensor.
As a base start I downloaded the NRF5 SDK V15.3.0 and modified twi_sensor_pca10056 program...
Hi. I'm using nRF52832, SDK13.0.0.
I should use SHA256 and MD5.
I made my code as below.
NRF_CRYPTO_HASH_CREATE(init_packet_hash, SHA256); NRF_CRYPTO_HASH_CREATE(init_packet_md5...
Hi. I'm using nRF52832, SDK13.0.0.
I want to use SHA256 as below.
output32Byte = SHA256[input32Byte];
Which function or example can I refer to?
And also I want to...
I tried to port the example "ble_app_ipsp_initiator" to pc-ble-driver and run on Linux. The peer device is another PCA10056 device running ble_app_ipsp_acceptor. The problem...
hi...
i want to use two uarts in nRF52840 , one uart to one pc and another uart to another pc .Data should be transferred and received between the nRF52840 and pc how can...
Hi, i'm using two nrf52840 DK ev kit. One it's the central and one the peripheral
After the connection I need to save power at the peripheral board, because the cpnsumptio...
Hello all,
I am developing application for evaluation board in which i am using 5 services. When I flashed my application on board it was unable to advertise. Then i checked...
Hello,
I'm using the nrf51422 with 210 softdevice.
I'm trying to figure out a way for the receiving slave device to go to sleep when away from the master, but to wake...
I am trying to set up the WDT on a nRF51822, but the timing doesn't seem quite right. If I load the CRV register with a count of 32768 I would expect it to be a one second...
I'm new to Nordic devices and tools. I have experience with Eclipse but I was wondering if there is a guide to help with the creation of a brand new project under Eclipse...
Hi,
As have been discussed earlier there is a problem with iOS device losing CCCD values on reconnect or turning bluetooth ON/OFF.
A patch for the ANCS sample is presented...
Hello Gentlemen,
Is it possible to know the passkey before the BLE_GAP_EVT_PASSKEY_DISPLAY event?
my nRF sensor is set as a display only and my central is an Android...
Hi all,
we are using the nRF51822 together with another module that provides an 1.8V UART only (LO = 0V, HI = 1.8V). Other IC´s on the device are using 3V Vdd and are connected...
I would like to make two BLE single mode devices to communicate with each other and Bluetooth v4.1 supports that, I was wondering if any of Nordic's modules support v4.1?
Referring to page 58 of the reference manual there is a ANAEN control signal that will contect a gpio pin to a corresponding analog input
I am using GPIO P0.01 -> AIN2...
I have started "playing" with the nRF51822 eval kit and the LED-Button example explained in the nAN-36. I wanted to know how is the UART port configured but I have not found...
Is it possible to count pulses with the 51822 from an external device in the range of 250-15.000 pulses pr. second, while the CPU is powered down (softdevice sleep)?
I...
To be able to upgrade FW through UART, a bootloader for nrf51822 is required in my project. I have tried out the example bootloader in SDK. But this example is using softdevice...
I followed the forum posts and nan-29 to get eclipse 4.3.2 to successfully connect to JLinkGDBServer via a Segger J-Link EDU on Ubuntu Linux.
I can start the GDB server...
