Hello everyone!
I want to form an Openthread network with three Nordic nRF52840 cardboards. I would like to monitor the traffic using a sniffer, but i can't receive any...
We are using the development board PCA10040 for implementing a prototype with several GPIO interruptions.
We are trying to use the NFC pins (pin 9 and 10) as pins of GPIO...
Development Software:
nRF5 SDK for Mesh v3.1.0
SEGGER Embedded Studio for ARM v3.50
SoftDevice S140 v6.1.0
Computer Platform:
Windows 10 Professional
Hardware...
Dear,
software/hardware:
nrf52832 mesh sdk v3.1.0
Q1: when friend feature node code can get? now just is bin file.
Q2: mesh has just four feature devices, friend feature...
It seems the LTE-M / NB IoT isn't available Europe-wide yet, and roaming applies country-wise.
Can anybody share his/her experience of using the BLG840F?
thank you.
Hi,
I am trying to build a thread network using a border router nRF52840 with a Raspi3B+ and 2 others end-devices nRF52840 connected on a CPU Ubuntu 16.04 LTS.
I have...
Hi,
I have a nRF52 DK board and I am trying to build a BLE peripheral with both connectable advertisement (custom with my own name and service) and unconnectable advertisement...
i changed the net-core flash partition and saved it to pm_static.yml. everything is ok while i build multi-image(mcuboot, cpuapp, b0n, cpunet) until my partner wants to build...
hello Nordic
i am working with nrf52840, zephyr rtos.
i can preform dfu via mcumgr cli (command line interface) or via nrfConnect application on my cell phone.
however...
Hi,
we are trying to use waveshare 2.9 epaper display with nrf52832, converted stm32 sample code to nrf52 with no luck. It seems we can not send command and data correctly...
Hi team ,
I am using 15.3 sdk and NRF52832 hardware. and Tool - SEGGER Embedded Studio for ARM 4.30c
I have developed code with DFU feature and and generated .hex file...
Hi,
I want to disable the UART of MCUBOOT to reduce power consumption. I searched in the DevZone and got the answer as below.
I followed the answer above, and created...
Hi there,
For the nRF5340, I read it support the Zigbee . So I just wanna know does it support the Zigbee frequency band in China, which is 780M?
Thanks,
SDK: 15.3.0 SoftDevice: S132 Device: EYSHJNZWZ (nRF52832)
I know there is the following documentation. ・ SEGGER Embedded Studio Reference Manual : https://studio.segger...
Dear all
I'm using the SD s140 and nRF52840 along with one of the latest SDKs (17...). Everything works fine, I'm able to start advertising and connect, but from time to...
As the title says,
I combined the TWI function with the ble_app_uart example and the three i2c sensor communication was successful.
However, when I added SPI to develop...
Hello, I'm new to nRF Connect SDK.
I managed to add the blinky example to build. I added a custom board.
There is a prf.conf project file with just CONFIG_GPIO=y I'm now...
I'm trying to get the device ID of the lis3dh accelerometer on a Thingy:52
nrf_drv_twi_tx returns 3 as an error. This means NRF_ERROR_INTERNAL --> "If an error was detected...
Hello, when i try to flash my card, (nrf52840) in visual studio code i have those errors
ERROR: The file specified is not a valid hex file, has data outside valid areas...
I am trying to build an application that can switch into MCUBoot's serial recovery mode and receive a new firmware image over the serial port. I'm using NCS 1.7.1 through...
I'm using the nrf9160dk (ns). I started an application based on the SIMPLE_MQTT sample. At first, every this worked. I added my one MQTT client with a different set of buffers...
Hi,
The LE Secure Connections Multirole Example is automatically requesting a pairing/bonding.
Why is it not first just doing a connection and requesting the numeric comparison...
