Hi,
firstly, I have to say, I use MBED OS, if you cannot help me because of this, I understand, but maybe somebody still has some general Ideas.
I am trying to build an...
Hi everyone,
Currently, I am working on my bachelor thesis for creating simple network by using MQTT, BLE-6LoWPAN and nRF52832. I have three nodes of 52832 and one raspberry...
Hello everyone!
I want to form an Openthread network with three Nordic nRF52840 cardboards. I would like to monitor the traffic using a sniffer, but i can't receive any...
We are using the development board PCA10040 for implementing a prototype with several GPIO interruptions.
We are trying to use the NFC pins (pin 9 and 10) as pins of GPIO...
Development Software:
nRF5 SDK for Mesh v3.1.0
SEGGER Embedded Studio for ARM v3.50
SoftDevice S140 v6.1.0
Computer Platform:
Windows 10 Professional
Hardware...
Dear,
software/hardware:
nrf52832 mesh sdk v3.1.0
Q1: when friend feature node code can get? now just is bin file.
Q2: mesh has just four feature devices, friend feature...
Hi,
We would like to interface with our nRF52840-DK from a PC.
We need to be able to send\recieve data from PC -> 52840 using Nordic's UART service.
We are looking for...
Hi,
We are the company which widely use your products in our devices. Currently we have the nRF9160 based device which have permanent trouble with radios. I want to ask...
Hi All,
Is there a tool or app that shows a visualization of Thread RSSI?
Any help would be appreciated, thanks in advance.
Best,
Tao
Ref:
https://devzone...
Hi,
I am developing both Central and Peripheral devices with nRF52840. For consistency, both are using SDK 15.3.0 and S140 V7.
I am able to connect to peripherals and...
Hi,
I was try to import modul nrfxlib in extising cmake project. My IDE is Eclipse CDT. Version of Zephyr is 2.4.0. Reason to do that, was testing SoftDevice BLE functionality...
We are using our board design using nRF52840.
During bringup I noticed that I could not run the Softdevice and the SPI driver simultaneous. After a bit of debugging it boiled...
I'm trying to send radio frame in timeslot but it's not working. From what I see with an spectrum analyzer, only the first frame is sent.
I am able to make the radio works...
Hi,
We are developing an application with a custom nrf5340 board in which beacons are sent periodically every 100ms. We have been analyzing power consumption with a Power...
Hi there!
We faced the problem of not being able to perform Legacy DFU with Android 10 and newer iOS devices and have since applied the fix. However, since doing so we observed...
Hello,
in our design we use a RF switch behind the ANT LTE antenna I/O of the nRF9160. Many RF switches need DC blocking capacitors in series with the RF signal due to their...
Hi everyone,
When we want to enable a module we usually enable it from the sdk_config.h by setting the desired module to 1 (for example #define NRFX_SAADC_ENABLED 1). I...
Hello, I am using nrf52810 and S112 Softdevice.
After initializing uart, use uart close for uart sleep.
Then the uart close will be checked.
I want to make an uart init...
I have an nrf52832 based device and a mobile app that I'm working on. I'd like to be able to turn the device on via the app, so wake on BLE seems the way to go.
I'm a neophyte...
Hi,
I am working nRF52832 and sdk 16 version. I want to get the RSSI value of my peripheral device nRF52832 and send it to central (phone) over ble ? how to do that ?
...
