I want to be able to read the gyro and accelerometer values from the MPU6050 sensor.
As a base start I downloaded the NRF5 SDK V15.3.0 and modified twi_sensor_pca10056 program...
Hi. I'm using nRF52832, SDK13.0.0.
I should use SHA256 and MD5.
I made my code as below.
NRF_CRYPTO_HASH_CREATE(init_packet_hash, SHA256); NRF_CRYPTO_HASH_CREATE(init_packet_md5...
Hi. I'm using nRF52832, SDK13.0.0.
I want to use SHA256 as below.
output32Byte = SHA256[input32Byte];
Which function or example can I refer to?
And also I want to...
I tried to port the example "ble_app_ipsp_initiator" to pc-ble-driver and run on Linux. The peer device is another PCA10056 device running ble_app_ipsp_acceptor. The problem...
hi...
i want to use two uarts in nRF52840 , one uart to one pc and another uart to another pc .Data should be transferred and received between the nRF52840 and pc how can...
Hi, i'm using two nrf52840 DK ev kit. One it's the central and one the peripheral
After the connection I need to save power at the peripheral board, because the cpnsumptio...
In mesh example project “dimming_server”，I have added functions: mesh serial, SAADC(use ppi) and compie pass.However,when debugging,an error is happened in the function"nrf_drv_timer_init...
Hardware: nRF52832
SDK 14.2
Segger Studio
Hello Sir or Madam,
We've made a new hardware variant of a previous design with an nRF52832 on much smaller form factor...
I use the QSPI(SDK15.2) of NRF52840 to read and write FLASH. Every time I open QSPI function, QSPI is closed after writing flash, but after close QSPI, there will be occasional...
Hi,
I want to capture data from TWI ADXL345 and send them by ble_nus_data_send() to mobile. Timing of data sending is done by application timer. My problem is that when...
Hi,
I tried to merge ble_app_multilink_central and ble_app_uart_c.
But, when I run the project It errors like below
I thougt the problem is the address of RAM_START...
HI,
my new BLE project is using nRF52810 chipset. Following is the requirements:
1. BLE nRF52810 will pair with iphone/android taplet
2. iphone/android table will...
Hello All,
I am using "nRF52840-DK" with "nRF5_SDK_for_Thread_and_Zigbee_v3.0.0_d310e71" SDK which i am using with SEGGER Embedded Studio(SES) .
I tested the "Blinky"...
Hi, weird issue. I am using the nRF toolbox to connect the nRF52832 (configured for HRM) for use on android. The thing is, on my personal phone ( Samsung galaxy s10+) everything...
Hello.
I have several problems with building this demo: https://github.com/NordicPlayground/thingy52-mesh-provisioning-demo As author recommends:
Download and extract...
Hi,
I would like to increase the length of read & write characteristic value to 29 bytes. I changed the NRF_SDH_BLE_GAP_DATA_LENGTH = 36 & NRF_SDH_BLE_GATT_MAX_MTU_SIZE...
Hi,
I try to build a simple BLE central device from nRF52840 dongle.
Using Nordic's nrf Connect desktop application I upload connectivity FW.
I want to replace nrf...
Hello,
To the nordic experts, please share your opinion or any suggestions are welcome in finding the feasibility of nRF52832 SOC in our product based on the information...
If I go into a power save management, can still set any digital GPIO as an output without consuming current.
Push-pull?
For example I connect the GPIO to the Gate-Mosfet...
