hi...
i want to use two uarts in nRF52840 , one uart to one pc and another uart to another pc .Data should be transferred and received between the nRF52840 and pc how can...
Hi, i'm using two nrf52840 DK ev kit. One it's the central and one the peripheral
After the connection I need to save power at the peripheral board, because the cpnsumptio...
In mesh example project “dimming_server”，I have added functions: mesh serial, SAADC(use ppi) and compie pass.However,when debugging,an error is happened in the function"nrf_drv_timer_init...
NRF52840 support the long range bluetooth and BLE gateway SDK, look at here that RAK Wireless held a Beta and welcome the community to participate.This board with Cellular...
Good day!
Started to work with nRF mesh. And wanted to add ir_lib from this project to Generic OnOff example.
And Source navigator shows error: static_assert failed "unspecified...
You have dead links everywhere and no obvious location for the gcc command line tools. Where is this?
Here are dead links:
https://infocenter.nordicsemi.com/index.jsp...
Hello!
Our current project is bare metal and has logging over CLI. I'm in the process of setting up a new project of ours that uses FreeRTOS but reuses a lot of the same...
HI,
I am using nrf52832 dk. I have a sensor that gives a negative voltage. I want to measure the value using saadc.
and can I use differential mode saadc for negative...
Hello All,
I am working on the N51822 custom board.
Using segger IDE, SDK 12.3
Previously i have worked on the sdk 14.3 on the n52810 board. It is working properly...
Hello
I am using pin 1.15 of nrf52840 dongle with transistor with enable pin of another chip. The other chip is a wifi chip which I only want to switch on whenever I have...
Hi All
I am using nRF9160 DK version 0.8.5, and I have gone through this link, downloaded and Installed all the steps, given there. All seems to be running good.
But some...
Hi I am using the custom_bluetooth_service tutorial from https://github.com/bjornspockeli/custom_ble_service_example with SDK v15 and nrf52840 DK.
I am now trying to use...
Win10 + Segger embedded studio
I can get the pca10059 blinky example to work. ( C:\nRF5_SDK_15.3.0_59ac345\examples\peripheral\blinky )
I use the NRF connect Programmer...
We are trying to receive high speed data using UART. Currently our source is set to transmit an 8 byte packet once every second.
I have initialised the serial port in IRQ...
Is there a public bug-tracker available (even better: publicly hosted repository)? I'm currently trying to wrap the SDK in way suitable for our internal processes (CMake,...
Hi,
i'm using "cycling speed and cadence" on DK to make a test run. However, my bicycle-watch(base on ANT) doesn't receive any "ANT signal".
Searching in the devzone,...
On the picture channel 2 connected to reset button on PDK.
UART channel drops to GND 4ms after button pressed.
How to prevent this?
Tried this: https://devzone.nordicsemi...
Hello,
at 3.3V the current consumption of my development kit is about 21.5 µA.
Due to the law of energy conservation, I would expect the current at 1.8V to be a little...
Hi,
i'm not getting any signal with a fresh DK and the latest modem driver.
entering AT+COPS=? will make it unresponsive forever. (nordic LTE Link monitor times...
I am combining several of the examples along with my own code. Specifically, I'm taking the Event Manager sample and combining it with some custom UART code and modified GPS...
Hi,
I would like to check my understanding of exactiy how the sourcing and configuration of the LFCLK works when using a WDT and doing soft resets.
I found these statements...
Hi,
I'm trying to use the BSP functions to do the following.
1. Detect three different button pressing types. First - singular quick press, Second - Long Press with Timeout...
