Hi. I'm using nRF52832, SDK13.0.0.
I want to use SHA256 as below.
output32Byte = SHA256[input32Byte];
Which function or example can I refer to?
And also I want to...
I tried to port the example "ble_app_ipsp_initiator" to pc-ble-driver and run on Linux. The peer device is another PCA10056 device running ble_app_ipsp_acceptor. The problem...
hi...
i want to use two uarts in nRF52840 , one uart to one pc and another uart to another pc .Data should be transferred and received between the nRF52840 and pc how can...
Hi, i'm using two nrf52840 DK ev kit. One it's the central and one the peripheral
After the connection I need to save power at the peripheral board, because the cpnsumptio...
In mesh example project “dimming_server”，I have added functions: mesh serial, SAADC(use ppi) and compie pass.However,when debugging,an error is happened in the function"nrf_drv_timer_init...
NRF52840 support the long range bluetooth and BLE gateway SDK, look at here that RAK Wireless held a Beta and welcome the community to participate.This board with Cellular...
Good day!
Started to work with nRF mesh. And wanted to add ir_lib from this project to Generic OnOff example.
And Source navigator shows error: static_assert failed "unspecified...
The nRF52810 datasheet shows the EVENTS_COMPARE register as RW, so I'm assuming that I can write to it.
But when I write to it, nothing happens.
Example.
I set up...
The question in short form is, is there any way to not use the Flash for storing bonding information and instead do this in RAM?
For the longer explanation:
We are using...
Hi,
We've circled back to this problem, now that we've increased speed.
We're using UART to communicate between the nRF52832 and an STM32.
Recently we increased the...
Hi,
I am trying to read UART data which is populated from another device going into the nordic board.
However, I am unable to read this data. I am using the ble_app_beacon...
Hi,
We are running a setup that pumps sensor data from light switch server to light switch client. After provisioning/configuration the setup is working fine without any...
Hi all,
I am try to test light switch server example in mesh SDK (v3.2.0) with nRF5 SDKs(v15.3.0). Using Coded PHY(125kbps) as this post or standard PHY (1Mbps) seperately...
Hi Devzone!
I'm using the fft function to check the frequency of sound from mic sensor.
All seems good but, o nly up to 2500hz is shown and the frequency above it is...
Hello,
I am trying to measure the battery voltage on an nRF52840 DK using SDK 15.3, while consuming as little power as possible, so by using nrfx_saadc_sample_convert()...
The example initializes the SAADC driver and configures one channel to sample analog input 0 (GPIO pin 2).
I would like to know how to change analog input pin to other GPIOs...
I'm working on nRF52840 SDKV15.3.0 SoftDevice S140. When setting 2mbps mode and long range mode getting <error> app: Fatal error .
i'm using xenon iot development kit its...
Hi all,
My project involves a ble-central initialising peripherals and creating a bond. When this is complete the peripheral should go into sleep mode and only wake up when...
Hi Everyone!
I checked this links https://infocenter.nordicsemi.com/pdf/nRF9160_DK_User_Guide_v0.9.pdf#page=20 and https://github.com/NordicPlayground/fw-nrfconnect-zephyr...
Can we enable more than 8 GPIO interrupts? It seems like GPIO_MAX_CHANNELS is 8 but we need more than 8 interrupts in our application.
How do we do this?
Hello everyone, I have an external board with processor nrf51422 and sensor BNO055 (I2C). I have a processor code created by someone else and I have a problem getting data...
