Hi. I'm using nRF52832, SDK13.0.0.
I should use SHA256 and MD5.
I made my code as below.
NRF_CRYPTO_HASH_CREATE(init_packet_hash, SHA256); NRF_CRYPTO_HASH_CREATE(init_packet_md5...
Hi. I'm using nRF52832, SDK13.0.0.
I want to use SHA256 as below.
output32Byte = SHA256[input32Byte];
Which function or example can I refer to?
And also I want to...
I tried to port the example "ble_app_ipsp_initiator" to pc-ble-driver and run on Linux. The peer device is another PCA10056 device running ble_app_ipsp_acceptor. The problem...
hi...
i want to use two uarts in nRF52840 , one uart to one pc and another uart to another pc .Data should be transferred and received between the nRF52840 and pc how can...
Hi, i'm using two nrf52840 DK ev kit. One it's the central and one the peripheral
After the connection I need to save power at the peripheral board, because the cpnsumptio...
In mesh example project “dimming_server”，I have added functions: mesh serial, SAADC(use ppi) and compie pass.However,when debugging,an error is happened in the function"nrf_drv_timer_init...
NRF52840 support the long range bluetooth and BLE gateway SDK, look at here that RAK Wireless held a Beta and welcome the community to participate.This board with Cellular...
I am developing based on "nRF5_SDK_15.0.0_a53641a" [Ble_app_uart], but I am not using LOG in my development environment. If LOG related items in "sdk_config.h" are invalid...
[Ble_app_uart] of the old version of [nRF5_SDK_14.2.0_17 b948 a] is operating correctly, not due to the low-speed clock.
In the old version, the operation of the crystal setting...
I'm trying to get the TWIM peripheral up and running on a custom board with an NRF52810 running SDK15 and S112.
My board is properly advertising, and publishing our custom...
After nightmares with Eclipse I managed to setup Segger within 5 minutes and flash, using the guide from here .
That guide show a lot of very specific stuff you have to...
I have the following ADC code: bitbucket.org/.../eakpq
I have been trying for the past few days to get this code to just perform a single ADC scan, on five channels, once...
Hi,
I use ble_ant_app_hrm example on 41822.
I set advertising time is 10 secs then I will get a timeout event from stack. When I get this timeout event, I will put the...
Hi
I am trying to use DFU feature using nRF5_SDK_14.2.0_17b948a. I used given preexisted example hex files for bootloader and app and successfully able to use DFU feature...
Develop environment:
BLE: nrf8001(non-connectable mode)
MCU: MSP430F5529
Problem:
I would like to use MCU's timer interrupt to wake up nrf8001 for broadcasting....
I perform some time critical task in my application and sometimes this task fails. Before executing the task I make sure that my device in not in BLE connection and ADV is...
Hi,
I'm looking for an example of how NRFX_UARTE works.
I would like to set up a serial port with EasyDMA to send and receive a thirty bytes.
Thanks in advance for your...
Hello, I am developing ble scanner in which I want to print data of adv reports over uart. Printing is executed in main and in on_ble_evt function I add items to circular...
Hi Expert,
I saw Nordic infocenter said that " HID Keyboard Application is not power optimized! "
I am going to optimize the power consumption,but I don't know how to...
Hello. I am able to send simple text using nRF Connect app to the nrf52832 and write received data to the SD card. So I want to send file (mp3, txt, jpg etc) and write this...
So I've been searching around for an answer to this on these forums and I can't really find what I'm looking for.
I'm using a RedBear BLE Nano v2 to act as an intermediate...
