I'm searching for a software engineer who can help us getting OTA support between nRF52810 and PIC16 MCU.
nRF52810 must have command- and data mode over UART, Pic controler...
I want to be able to read the gyro and accelerometer values from the MPU6050 sensor.
As a base start I downloaded the NRF5 SDK V15.3.0 and modified twi_sensor_pca10056 program...
Hi. I'm using nRF52832, SDK13.0.0.
I should use SHA256 and MD5.
I made my code as below.
NRF_CRYPTO_HASH_CREATE(init_packet_hash, SHA256); NRF_CRYPTO_HASH_CREATE(init_packet_md5...
Hi. I'm using nRF52832, SDK13.0.0.
I want to use SHA256 as below.
output32Byte = SHA256[input32Byte];
Which function or example can I refer to?
And also I want to...
I tried to port the example "ble_app_ipsp_initiator" to pc-ble-driver and run on Linux. The peer device is another PCA10056 device running ble_app_ipsp_acceptor. The problem...
hi...
i want to use two uarts in nRF52840 , one uart to one pc and another uart to another pc .Data should be transferred and received between the nRF52840 and pc how can...
Hi, i'm using two nrf52840 DK ev kit. One it's the central and one the peripheral
After the connection I need to save power at the peripheral board, because the cpnsumptio...
I've implemented monitor mode debugging as described here and it works great. When I get a hard fault, it doesn't break in the IDE anymore. So it appears to be running fine...
I can connect the kit to the nrf cloud and even add the device to the gateway but i cannot switch on and off the leds.Where is the source code for the nrfcloud example?I cannot...
Hi all,
I recently encounter this strange issue that I couldn't understand. My code works perfectly fine during debugging on all 52832 chips, but freezes without response...
For nrf52832, I use pstorage to set 254 blocks with 20 byte of each block, that will use near 5 pages.
now I fail to clear data all block together. pstorage_clear( &block_base_handle...
Using an nRF52832 with SDK 14.0.0, S132 SoftDevice
We are able to connect to the device with an iOS/Android phone just fine.
Upon disconnecting, a second phone is not...
Hi,
I'm trying using AES ECB encryption of peripheral drivers on development board with nRF52832 and PCA10040.
I inserted the following code before main loop of ble_app_uart...
i have a particular automotive tuning application where i have to deal with ignition and fuel injection timing (old stuff in the new e-mobility time)
here are some loose...
I'm a beginner to programming nRF devices in C, trying to graduate from Arduino (i.e. kindergarten).
I've installed Segger Embedded Studio and can compile and run SDK examples...
Hi, I have implemented a firmware that allows to bonding and connecting whit android and iOs; I have added the HID service and characteristics, if I press a button I can send...
I have 3 nordic boards each having different serial no so i need to develop a a structure with the information of the serial no and some revision number etc
and i need to...
hi everyone,i have a problem when i want to esase one block of flash memery,if i do it before ble_stack_init,it can work,but if i do it after ble_stack_init,my program will...
Hi,
We have made a custom PCB using the NRF52832 chip. While it was working fine for a couple of days, it suddenly stopped working and went to a hard fault. We are not...
hi:
i have a problem when i want to write data to flash.by the way,my program is running with no-system.
i found the program is always restared when i enabled erasing,
...
