Dear,
software/hardware:
nrf52832 mesh sdk v3.1.0
Q1: when friend feature node code can get? now just is bin file.
Q2: mesh has just four feature devices, friend feature...
It seems the LTE-M / NB IoT isn't available Europe-wide yet, and roaming applies country-wise.
Can anybody share his/her experience of using the BLG840F?
thank you.
Hi,
I am trying to build a thread network using a border router nRF52840 with a Raspi3B+ and 2 others end-devices nRF52840 connected on a CPU Ubuntu 16.04 LTS.
I have...
Hi,
I have a nRF52 DK board and I am trying to build a BLE peripheral with both connectable advertisement (custom with my own name and service) and unconnectable advertisement...
Hi,
I'm exploring the hid peripheral example with 52832 Dev Kit and made it working correctly. While, when I was tring to connect to it with nRFConnect, I found that the...
Hi,
I'm exploring the hid peripheral example with 52832 Dev Kit and made it working correctly. While, when I was tring to connect to it with nRFConnect, I found that the...
I have a PCB with an nRf51822 @1.8V, using the SDK 10 (no chance to change it).
The PCB itself with everything but the nRF (we did not iron it on purpose to measure consumption...
I’m trying to debug an existing product by opening its old firmware project on a new PC. The project uses nRF5 SDK for Mesh v2.1.1 , SoftDevice S132 , and nRF52832 .
I installed...
I am currently working in project with nrf54l15dk and 3.0.2 sdk. I'm trying to work with peripherals and I want my project to do the following: -Have 2 PWM outputs that used...
Hi DevZone Community
I'm trying to get a simple Hello World sample to run on an nRF5340DK board with a 2.8" ILI9341 based TFT display that has Arduino headers attached ...
Hello,
Im currently in the process of integrating Memfault OTA on the nRF9151 DK. My project has multiple boards: nRF9151 DK connects with nRF52840 DK via UART for communication...
Hi!
I am using the nRF52832 for a small custom PCB for a wearable device and I would appreciate a review from the experts, before proceeding with manufacturing :)
The...
Hi,
I have a FAT file system that I use with an USB Mass Storage feature. I use the mx25r64 NOR flash (the same as the nrf7002dk evalboard). I am working on ncs 3.0.2. ...
TLDR:
I'm working on getting LE Audio working on a Raspberry Pi CM4 setup and running into some frustrating issues. I've got a u-blox NORA-B126 module (with the nRF5340...
Hi nordic engineer
I have a product use nrf52832. And have two project,project use nrf5 17.0.0 SDK and MDK.
The project A choose chip nrf52832 and S132
The project B...
Hi
The nRF54L15-DK suite tests the accuracy of channel sounding, all ncs versions are v3.1.1. I am using the channel_sounding_ras_initiator and channel_sounding_ras_reflector...
Hello,
At my company, I am working on a board with an nrf54L15, equipped with an SX1261 and an ADC MCP3461R.
I started development with SDK 3.0.2 and everything is working...
Hello!
With nRF52, nRF5 SDK and SoftDevice S130, we were using some of the Radio's PPI events (e.g. EVENT_END) for some functionality.
Now we plan to move to nRF54L and...
When running the channel sounding example on the nrf54l15, how can one obtain the IQ values of the ranging signal?I want to obtain the IQ value and then use my own algorithm...
Hello,
I have tested a thread network with a nRF52840 SDK programmed with Thread COAP Client sample and two nRF52840SDK programmed with Thread COAP Server sample.
All...
I've built a project based on the peripheral_uart appliction. This is working well, but I need to now sort out the lowpower mode. My product is battery powere & I need to...
I’m using the nRF54L15 to test throughput. I want to connect a single board to any arbitrary BLE device to test GATT throughput. Is there any way to do this? Are there any...
