Using one ADC, the current can be reduced to about 40uA after the ADC value is taken. Using a two-channel ADC, after the ADC value is taken, the current stops at about 0.4...
I'm searching for a software engineer who can help us getting OTA support between nRF52810 and PIC16 MCU.
nRF52810 must have command- and data mode over UART, Pic controler...
I want to be able to read the gyro and accelerometer values from the MPU6050 sensor.
As a base start I downloaded the NRF5 SDK V15.3.0 and modified twi_sensor_pca10056 program...
Hi. I'm using nRF52832, SDK13.0.0.
I should use SHA256 and MD5.
I made my code as below.
NRF_CRYPTO_HASH_CREATE(init_packet_hash, SHA256); NRF_CRYPTO_HASH_CREATE(init_packet_md5...
Hi. I'm using nRF52832, SDK13.0.0.
I want to use SHA256 as below.
output32Byte = SHA256[input32Byte];
Which function or example can I refer to?
And also I want to...
I tried to port the example "ble_app_ipsp_initiator" to pc-ble-driver and run on Linux. The peer device is another PCA10056 device running ble_app_ipsp_acceptor. The problem...
hi...
i want to use two uarts in nRF52840 , one uart to one pc and another uart to another pc .Data should be transferred and received between the nRF52840 and pc how can...
We are about to use the nRF52832 and are looking at which SofDevice to select for a Central-only implementation. The S122 summary says it targets the nRF52820 and nRF52833...
i m using NRF52840 with sdk 15.2. In that i m testing direct test mode by UART.Now i can do transmit mode.i can check through nrfconnect dtm mode. i cannot check receiver...
Hi,
I tried the following AT settings on the nRF9160 DK board:
AT+CPSMS=1,,,"00111000","00011110"
AT+CFUN=1
After this the modem enters PSM mode and the current is...
Hi,
One of our modules using PCA10090 0.8.2 programming and production nRF9160/nRF52840 modules.
Our customer reported that they can't use PCA10090 0.9.0 re-programming...
Hi! I ran into a little misunderstanding in setting up clock frequency for PDM. I need to work with lower clock frequency than default - 0.64 MHz. I see, that PDM_CLK = 32...
Hi,
Some questions on the scan consumption of nRF52840 and using the attached Online Power Profiler for BLE as reference
If I am using my nRF52840 to scan 24hours at...
I wish to merge the cloud_client example with GPS example. How should I go about it? Along with main.c files of both, which other files will I need to merge?
I am currently making a program that will interpret serial commands from UARTE1 and then send + read something from the other (UARTE0). Previously, when I have been using...
Hello,
I want to be able to send 1 MB of data from a server node to a client node
I have made a simple model with an array that holds 300 bytes.
and upon a timer the...
Hi,
I want to connect Multi peripherals to one central and want to send the device name(peripheral which is connected) through the uart.
How do i get the device name which...
I have seen some variations of this issue but hoping someone can lead me in the right direction.
Similar to others, I am using NRF_LOG_INFO for debug messages. It works...
Hello, I am working on a project which uses nrf52832 module ( https://www.seeedstudio.com/MDBT42Q-nRF52832-based-BLE-module.html ). I just want someone to review its circuit...
Hi!
I'm slightly confused with the documentation regarding softdevices S112 and S113. Among other differences, its noted that SD S113 does not support nrf52820 chipset while...
Hi, I have a custom board based on nRF9160 for which I created custom .dts following porting guide. It seems TX isn't sending anything (stay close to 0V) - config I have is...
