I have a simple TCP client application running on the nRF9160. After connection to the server, recv is called and writes the data over Segger RTT channel 1, where on the host...
Hi,
firstly, I have to say, I use MBED OS, if you cannot help me because of this, I understand, but maybe somebody still has some general Ideas.
I am trying to build an...
Hi everyone,
Currently, I am working on my bachelor thesis for creating simple network by using MQTT, BLE-6LoWPAN and nRF52832. I have three nodes of 52832 and one raspberry...
Hello everyone!
I want to form an Openthread network with three Nordic nRF52840 cardboards. I would like to monitor the traffic using a sniffer, but i can't receive any...
We are using the development board PCA10040 for implementing a prototype with several GPIO interruptions.
We are trying to use the NFC pins (pin 9 and 10) as pins of GPIO...
Development Software:
nRF5 SDK for Mesh v3.1.0
SEGGER Embedded Studio for ARM v3.50
SoftDevice S140 v6.1.0
Computer Platform:
Windows 10 Professional
Hardware...
Hello,
I am using SDK 15.3 for the development. During the upgrade process I wanted to send the hardware version when requested by the host.
I have made the changes...
I want to use P0.10 of NRF52810 as GPIO. I have added CFLAGS += -DCONFIG_NFCT_PINS_AS_GPIOS in the make file. But still its not working. I am using Nrf 52810 , SDK 15.2.0...
Hello,
I recently decided to upgrade an Arduino project to you nice and well documented products :)
I successfully built and run the example provided here and tried...
Hello! I'm interfacing a sensor with an nRF52840 development board and have run into a few issues:
1) I have a check status function as shown below:
bool ADXL_check_status...
Hello, I'm working on timeslot and RADIO on nRF52840.
I found a sample code which sets 1 to "NRF_RADIO->POWER" to initialize RADIO peripheral.
-----------------------...
Using nRF52832, SDK16, SD132.
I have a (background)bootloader which is derived from dfu "secure_bootloader" example.
When there is nothing to flash bootloader successfully...
The hid keyboard in the routine is buggy. The first problem is that after A device is connected, it is disconnected and other devices cannot be paired. The second problem...
I'm debugging an issue which triggers app_error_fault_handler() and it indicates id=NRF_FAULT_ID_SD_ASSERT, PC=0x18434, and info=0.
This address falls in SD, and how can...
Hello,
I am working on MQTT sample ncs\nrf\samples\nrf9160\mqtt_simple. I am sending data from UART and I2C to the mqtt server. For sending data I am using Workqueue thread...
Hello,
I need to bond a device with its bd_addr using AT_command and unbond device using another AT_command. I am having only DK of nrf52832. So I am trying to bond 2 devices...
Hi,
I'm quiet new with nrf9160.
I try to mix the two sample GPS and MQTT to send my position each time it change to a MQTT broker.
I have create two threads, one for...
Hi, I'm using nRF52 DK to develop and PPK v1.1.1 with Power Profiler app on nRF Connect v3.3.1 to measure current.
1. I see a lot of posts referencing the firmware on the...
Hello.
I have a issue about missing NRF_DRV_SAADC_EVT_DONE event in saadc handler.
setup is 52832, SDK 15.3.0, S332. enable ANT, BLE
for battery, sensor, I use 2 adc...
When I run the BLE peripheral HRS example on the eval board and try to connect with a Samsung XCover3 using the "nRF Connect" app, I got the error 22 (0x16): GATT_CONN_TERMINATE_LOCAL_HOST...
Hi, we are considering using Gazell on the nRF52840 with nRF5 SDK v16. What would be the maximum packet length and the maximum data throughput that we could expect? What would...
