It seems the LTE-M / NB IoT isn't available Europe-wide yet, and roaming applies country-wise.
Can anybody share his/her experience of using the BLG840F?
thank you.
Hi,
I am trying to build a thread network using a border router nRF52840 with a Raspi3B+ and 2 others end-devices nRF52840 connected on a CPU Ubuntu 16.04 LTS.
I have...
Hi,
I have a nRF52 DK board and I am trying to build a BLE peripheral with both connectable advertisement (custom with my own name and service) and unconnectable advertisement...
Hi,
I'm exploring the hid peripheral example with 52832 Dev Kit and made it working correctly. While, when I was tring to connect to it with nRFConnect, I found that the...
Hi,
I'm exploring the hid peripheral example with 52832 Dev Kit and made it working correctly. While, when I was tring to connect to it with nRFConnect, I found that the...
I have a PCB with an nRf51822 @1.8V, using the SDK 10 (no chance to change it).
The PCB itself with everything but the nRF (we did not iron it on purpose to measure consumption...
I have downloaded the motion_driver_6.12 for Nordic Thingy 52 as given in the readme.txt file. And I am using Segger Embedded Studio to build and debug the code. But the IDE...
Hello Everyone,
I am a beginner and working on nRF52832 DK using SDK v13 and using keil mdk armv5.as a compiler. I build it successfully, but when I loaded the hex file...
I am trying to update the firmware on the Thingy:91 following the instructions here: https://infocenter.nordicsemi.com/index.jsp?topic=%2Fug_nc_programmer%2FUG%2Fnrf_connect_programmer...
Hi
I am using nordic thingy 91 and i want to program my application on nRF9160 and nRF52840 respectively and i am following the getting start guide.
first i was able to...
SDK 17.0.0/ Windows/nRF52840 DK/ SEGGER
Hi, I want to learn how to achieve the outcome of allowing the peripheral to advertise in the long-range and the Central DK to pick...
Hello,
I have an application in which I need to get RSSI before, during and after any BLE connection has been made. The RSSI measurements are being used to quantify the...
Hello, I am using nRF52 DK and SDK V15.2.0 with a Nordic PPK to measure current draw. I have read tons and tons of questions posted here but am still unable to figure out...
Hi all :) ,
I'm trying to create my new zip folder with new image.
I connect to my nrf52833, then i click on dfu button into nrfConnect mobil app.
I selec zip file...
I'm using:
OS : Windows 10
IDE : Segger Embedded Studio for ARM Realease 4.52c Windows x64
SDK : nRF_SDK_15.0.0_a53641a
In my project I'm using 4 pressure sensors...
Hi,
I've been trying to make a small modification on the existing Nordic Thingy firmware, such as changing the color of an LED, by compiling the existing Nordic Thingy 52...
Hi,
I am trying to set up a region of RAM to store variables that persist across soft reboots but am unsure how to do it in this environment. I would normally define a region...
Hi Nordic ppl,
Is Nordic SoC supporting BlueZ package ?
Any specific SoC that we should be selecting to be able to run the .
Also, i believe all 3rd party Modules...
I am trying to implement openthread cli uart in pca10059, have made all modifications but the hex file is not getting burnt in bootloader mode using nrfconnect
/cfs-file...
Hi:
I use the PCA1004 EVK bord to configuer the I2S MCK as 256K, 32MHz/125 (I2S_CONFIG_MCK_SETUP 34340864) .
then I measure the pin use oscilloscope, but I only get 255K...
Hi Nordic support,
We had an "intermittent" connection failure with a BLE radio in one of our products under development, which exhibited itself with an <unknown> device...
Hello,
We want to use the flash to store two types of information: application configuration settings (which should be protected during DFU) and temporary data (which...
