hi........... folks
i am merging two programs together uart and TWI sensor ...using nrf52382 and segger 15.2version
i am getting the error in ble_nus_send ,
even i have...
Software and Softdevice: SDK 12.3.0 keil5
Platform: Windows 10
Hardware: NRF52832 DK
I am trying to combine WDT and FATfs together. But once I have both of them, there...
I am trying to get a good handle on the difference in average power consumption between BLE point to point and Zigbee on an nRF52840. We have battery powered products and...
Hi, For my project, I need to design a BLE packet sniffer which scanning the 40 channels. Therefore, I need 40 dongles are connected to a computer that can read and transfer...
I am writing code to get a nrf52840 DK to associate with an existing 802.15.4 coordinator using the 802.15.4 API module within SDK 15.2.
I've called "mlme_scan_req" and...
Currently, I am able to use Mqtt Publisher or Subscriber with only one Nrf52 device. I can ping to the device with link-local address.
I am using Nrf52832 with SoftDevice...
Hi everyone,
After days of figuring out how CMake works, I try to write a CMakeList.txt myself, and decide to put my progress on this community. Right now, using CLion with...
Hi, I'm trying to write an app to capture images from a camera and was wondering how to monitor changes on specifc defined pins in the board overlay file. For example if(...
The certification lab is testing nRF52840 RF .They need to test LE coded S=8,Payload Type：11111111：payload length：37
but i can't find Payload Type：11111111 in software nRF_DTM...
I am a beginner I want to advertise for some time then go to sleep mode and wake up do some tasks like advertising and go to sleep mode again. Do all this process recursively...
It looks like the nRF52840 only supports:
8 data bits
1/2 stop bits
even/no parity
So 7E1 is not a supportable mode...is this true? is there a possible work around...
Hi,
I am using nrf52840 and power it by voltage 3v using CR123A battery. As per datasheet minimum operating voltage is 1.7V. But i am facing controller reset at 2.5V. What...
How do we enable a PPI TASK for a GPIO output pin configured using zephyr GPIO driver API? ex: gpio_pin_configure_dt (&ex _pin , GPIO_OUTPUT );
If I just call nrfx_gpiote_out_task_enable...
Hi,
I'm having some trouble getting a device pointer for the OV7670 Camera. I've ported the OV7725 driver. It appears as if the program exits the driver before setting...
So I've been having an issue connecting JLink to programmer v2.2.0.
15:57:24.681
Using @nordicsemiconductor/nrf-device-lib-js version: 0.4.1
15:57:24.682
Using...
I'm trying to upgrade the nRF9160 modem FW on our nRF9160-DK. Programmer v2.2.2 indicates success but the at commands continue to return
at+cgmr
mfw_nrf9160_1.2.3
OK...
I am using the DPPI feature in the nRF5340 to trigger an SPI transaction from a GPIO edge with a delay.
In more detail:
GPIOTE IN event triggers RTC clear task
RTC compare...
Hello,
I've been trying to figure why calling sd_ble_gap_tx_power_set() continues to return the error NRF_ERROR_NO_MEM. I'm using SDK 17.0.2 with S113, v7.2.0 on the NRF52840...
Hi team,
Currently am working on PWM example from SDK i.e. (Nordic SDK v1.8.0), am testing the pwm example from the sample i'e v (1.8.0\zephyr\samples\basic\blinky_pwm)...
I have nrf52840 pcb without XTAL 32768Hz. When I flash it with Zephyr sample project "Peripheral uart" it doesnt work.
How can I config project to work without XTAL on the...
The application seems to stop at an instance where I invoke a Send call to send data over to a ble central, and the callstack looks as follows. Any way to narrow down the...
