hi........... folks
i am merging two programs together uart and TWI sensor ...using nrf52382 and segger 15.2version
i am getting the error in ble_nus_send ,
even i have...
Software and Softdevice: SDK 12.3.0 keil5
Platform: Windows 10
Hardware: NRF52832 DK
I am trying to combine WDT and FATfs together. But once I have both of them, there...
I am trying to get a good handle on the difference in average power consumption between BLE point to point and Zigbee on an nRF52840. We have battery powered products and...
Hi, For my project, I need to design a BLE packet sniffer which scanning the 40 channels. Therefore, I need 40 dongles are connected to a computer that can read and transfer...
I am writing code to get a nrf52840 DK to associate with an existing 802.15.4 coordinator using the 802.15.4 API module within SDK 15.2.
I've called "mlme_scan_req" and...
Currently, I am able to use Mqtt Publisher or Subscriber with only one Nrf52 device. I can ping to the device with link-local address.
I am using Nrf52832 with SoftDevice...
Hi everyone,
After days of figuring out how CMake works, I try to write a CMakeList.txt myself, and decide to put my progress on this community. Right now, using CLion with...
Hi,
We managed to integrate both normal BLE and mesh stack onto our working prototype, powered by nRF52840. So far, it is working well. We are trying to further maximise...
I am using the NRF52840 controller to connect BMD101(ECG sensor) uart based having a baud rate of 57600.
Note: Using UART peripheral example on SDK17
I am trying to parse...
Hi
I've problem on my design when I use voltage translator to communicate with sensors. Can you guys see pictures below:
1.nRF52840 using 3.3v:
1.nRF52840 using...
Hi all.
I want to send my packets in the negotiated time interval.
I sat the NRF_SDH_BLE_GAP_EVENT_LENGTH to 6.
The negotiated TI is 36 ms.
the results are
1- the...
Hello to all,
(If "TLDR" go to "### TLDR ###" in the bottom of the page, where you'll find the straight questions without all the context... ) Me and my team are using the...
Hi,
I noticed that the value raw_uuid_len in function ble_advdata_uuid_find() in module ble_advdata.c is fixed at the value UUID128_SIZE.
So the function can only find...
Hi, I am new to NRF and segger embedded studio.
So I want to send temperature sensor data connected with nrf52840 DK to the Murata1_SC device using UART.
The data will...
Found a potential "weirdness" with the mergehex utilty. When merging hex files containing code, dont seem to have an issue. Recently I was using mergehex create a full programming...
Hello Team,
Can you please confirm if we can use the crypto API to do AES encryption/decryption. Can I use it in non secure app and in application and not in bootloader...
Hi,
We want to make some BLE application for nRF52840 on Thingy:91. Referring to PCA20035 schematic, there are some spare pins which we assume is available for GPIO as...
Hi, we have a product (NRF51 SD8 S110 RBCMesh) on the market that craches about once per year the line that asserts is line 189 in src\\soc_radio_timeslot.c (your code) and...
Thanks in advanced. Platform is: nrf52832-qfaa, SDK_17.0.2, use V6.88a JFflash. I design custom board with cp2102n and nrf52832 to act as a usb receiver. All these boards...
Hi, I have flashed the nRF52840 dongle on macos (11.4) and ubuntu (20.04.20) using nRF Connect for Desktop (3.61) following the guide ( https://infocenter.nordicsemi.com/index...
Hi, I'm trying to run my app on a custom board, I keep getting the error "stopped by vector catch" before any of my code runs. I've tried sample programs for the equivalent...
