I have a simple TCP client application running on the nRF9160. After connection to the server, recv is called and writes the data over Segger RTT channel 1, where on the host...
Hi,
firstly, I have to say, I use MBED OS, if you cannot help me because of this, I understand, but maybe somebody still has some general Ideas.
I am trying to build an...
Hi everyone,
Currently, I am working on my bachelor thesis for creating simple network by using MQTT, BLE-6LoWPAN and nRF52832. I have three nodes of 52832 and one raspberry...
Hello everyone!
I want to form an Openthread network with three Nordic nRF52840 cardboards. I would like to monitor the traffic using a sniffer, but i can't receive any...
We are using the development board PCA10040 for implementing a prototype with several GPIO interruptions.
We are trying to use the NFC pins (pin 9 and 10) as pins of GPIO...
Development Software:
nRF5 SDK for Mesh v3.1.0
SEGGER Embedded Studio for ARM v3.50
SoftDevice S140 v6.1.0
Computer Platform:
Windows 10 Professional
Hardware...
Hi. I'm writing my own libraries for nRF52832 and I can't get UARTE to work.
Here is my code.
I'm using pins 6 and 8 as the UART example.
I wrote same code for UART...
I'm beginner with nrf chips.
I have a custom board with ntf52840 module. I connect board to stlink via swd interface, then check:
st-info --probe Found 1 stlink programmers...
I would like to perform observer role scanning i.e. passive scanning. I am using nRF52832, S132, SDK 15.2.0. I am trying as follows.
NRF_BLE_SCAN_DEF(m_scan);
static...
I am using the SDK5 development kit with Segger for a BLE application.
I found the Service for SES but the SDK doesn't seem to include the Pulse Oximeter service.
I would...
We are developing hardware to work as a AirMouse (Gyroscope based working mouse)
I am using SDK16.0 SES
I have seen that HID Mouse example
and i implement gyroscope...
I have bought a BLE Micro. ( www.seeedstudio.com/Seeed-Micro-BLE-Module-w-Cortex-M0-Based-nRF51822-SoC-p-1975.html) 1. I downloaded "nRF Connect App for Android" on the phone...
Hi there,
I've recently purchased an nRF52840DK with the 52840 SoC and I'm wanting to develop Bluetooth Mesh apps.
I'm on Mac OS X. Should I begin with the nRF52 SDK or...
Hi,
I just got the brand new Thingy:91 and would like to program it with an application earlier developed for the nrf9160 DK .
Further I'd like to use the Link Monitor...
Hi All,
Recently I have been working on nrf9160dk board. The use case is to have nrf9160 work as a serial LTE modem with GPS functionality. I have the following link https...
Hi,
I have implemented my own Vendor model, using the light switch client/server as a starting point. The model allows to send byte arrays. Since I have used the generic...
I am using SDK v16, SEGGER to program on my nrf52832 SOC for our project. I need to save a few variables to the flash memory. These variables will hold the status of the device...
Hello,
we are using SDK version 15.3 and mesh SDK version 3.2.0, on a nRF52840 DK board using the Segger Embedded Studio IDE version 4.52 (64-bit).
Our goal is to add...
Hello,
I followed this tutorial in order to familiarise with the code and understand better what is going on. Now, my question is the following, regarding challenge 2 :...
Hi,
I'm using latest master branch of nRF Connect SDK and pre-released modem FW 1.1.2 which is including ANT->AUX switching. I'm developing a firmware for a custom board...
Hello,
I notice that Thread examples with Softdevice (nRF5_SDK_for_Thread_and_Zigbee_v4.0.0_dc7186b) works fine for a PCA10056 but not on a PCA10059. When I had tried...
