Hi everyone,
Currently, I am working on my bachelor thesis for creating simple network by using MQTT, BLE-6LoWPAN and nRF52832. I have three nodes of 52832 and one raspberry...
Hello everyone!
I want to form an Openthread network with three Nordic nRF52840 cardboards. I would like to monitor the traffic using a sniffer, but i can't receive any...
We are using the development board PCA10040 for implementing a prototype with several GPIO interruptions.
We are trying to use the NFC pins (pin 9 and 10) as pins of GPIO...
Development Software:
nRF5 SDK for Mesh v3.1.0
SEGGER Embedded Studio for ARM v3.50
SoftDevice S140 v6.1.0
Computer Platform:
Windows 10 Professional
Hardware...
Dear,
software/hardware:
nrf52832 mesh sdk v3.1.0
Q1: when friend feature node code can get? now just is bin file.
Q2: mesh has just four feature devices, friend feature...
It seems the LTE-M / NB IoT isn't available Europe-wide yet, and roaming applies country-wise.
Can anybody share his/her experience of using the BLG840F?
thank you.
Hi, I am using sdk 12.3.0 sd130v2. I have the hardfault_implementation.c included in the project. But I am not able to keep breakpoint anywhere in that file. I have made HARDFAULT_HANDLER_ENABLED...
I have initialized SPI0 master by this code:
static const nrf_drv_spi_t spi = NRF_DRV_SPI_INSTANCE(0);
...
nrf_drv_spi_config_t spi_config = NRF_DRV_SPI_DEFAULT_CONFIG;...
Recently I have been working with the serial bootloader from SDK 11. I can upload a softdevice, and supporting application using this bootloader without issue, as long as...
I started working on mesh 51 series ,
Points for which we need inputs
Data packet size for transmission
Process for association and address assigning during commissioning...
Hi,everyone
I am using S132 and SDK13 to set two peripheral links,now i want connect two centers using different connection parameters at the same time,for example,connect...
Hi,
Can the nRF52832 support higher data rates:
UART TX baud rate of more than 1Mbps, such as 3 Mbps without bitbanging.
TWI of 1MHz
any trick to get them...
Hi,
I recently purchased the NRF52 DK. I'm using the ble_uart_example for the SDK 11. I'm using the softdevice PCA10040.
I noticed the the SDK 11 includes the RTT c...
I want to use the nrf52840 with DCDC in high voltage mode to drive the circuite directly from a LI-ION battery.
Is there any reverse current protection built into the chip...
When you start a receive task, what will the radio do if the HFXO is not stable? Not begin to ramp up until the HFXO is stable, OR begin to ramp up but not become active until...
nrf52832, returns an error even with parameters
IROM1: 29000 57000, IRAM1 3CC8 C338, softdevice_enable() works without errors.
#define PERIPHERAL_LINK_COUNT 1
#define...
im working on nrf51822 using sdk 9 ....i completed bonding using ble proximity example without privacy key.....now i wish to add privacy key ..what all changes i have to make...
I'm using the with SDK version 13.1.0 along with S140 SoftDevice v 5.0.0-3.alpha and trying to utilize the Bluetooth 5 Extended Advertising feature.
The function ble_advdata_set...
I'm periodically polling a TWI sensor with a blocking call, as in
ret_code_t err_code;
m_xfer_done = false;
err_code = nrf_drv_twi_tx(&i2c, address, subAddress, 1,...
My external application processor UART, every 5 ms @ 19.2 KBPS transmits a byte to UART RCV of NRF8001, which needs to convert this to BLE and then transmit to a cell phone...
