I am trying to get a good handle on the difference in average power consumption between BLE point to point and Zigbee on an nRF52840. We have battery powered products and...
Hi, For my project, I need to design a BLE packet sniffer which scanning the 40 channels. Therefore, I need 40 dongles are connected to a computer that can read and transfer...
I am writing code to get a nrf52840 DK to associate with an existing 802.15.4 coordinator using the 802.15.4 API module within SDK 15.2.
I've called "mlme_scan_req" and...
Currently, I am able to use Mqtt Publisher or Subscriber with only one Nrf52 device. I can ping to the device with link-local address.
I am using Nrf52832 with SoftDevice...
Hi everyone,
After days of figuring out how CMake works, I try to write a CMakeList.txt myself, and decide to put my progress on this community. Right now, using CLion with...
i am using nrf 52832, i got SAADC example code from sdk. that code done by using timer. i could not understand timer section. Is available SAADC simple example code without...
Hello everyone,
as indicated by this question https://devzone.nordicsemi.com/f/nordic-q-a/35692/adding-nrf52-dk-to-github-mesh-demo-for-thingys/138327#138327 I am trying...
Dear Nordic,
I am considering to make a board that includes an nRF5340 + display. I am looking at a display that supports QSPI and I was wondering if the nRF5340 QSPI can...
Hi,
I am learning nRF52840 development and making a sensor device.
The datasheet of the nRF52840 chip says:
Regulated supply for external components up to 25 mA
...
Hi,
I'm working on a project with the Nordic nRF9160 Development Kit and am trying to send Bluetooth beacon data from the nRF52840 chip to the nRF9160 chip using UART and...
Hello,
I try to enable the LE Data Packet Length Extension. According to the available documentation, it should be as simple, as adding `CONFIG_BT_USER_DATA_LEN_UPDATE=y...
When loading empty software (zephyr based) into the nRF9151, the nRF9151 uses roughly 4mA and when erasing the IC, it uses 5.8mA.
Does zephyr not include a power down mode...
Hello!
I am porting a nRF Connect v2.9.0 application from a nRF52 to the nRF54L15.
We are using PPI/EGU to get exact measurements for some BLE radio events for some optimizations...
Hi,
We are developing application software on the nrf9161dk that uses the little FS file system running on external FLASH. Most of the application development has been completed...
Hi
I want to use P0.18 gpio as output pin and not as reset for nordic.
I am using ncs v2.0.0.
I have added
CONFIG_GPIO_AS_PINRESET =n in prj.conf
and when i...
Hello,
I have a Nordic Thingy:91, and I need to perform continuous wave (CW) transmission tests in LTE. To achieve this, I plan to develop custom firmware that alternates...
Hello Everyone,
We are working on a new product using the nrf52840 and OpenThread.Our current product uses the Azure IoT Hub and we were wondering if we could use the library...
Hi,
I defined __STACK_SIZE as compile/build flag. It has no effect according to GCC output after building is done.
Chip is nRF52840.
I tried to set fixed stack size...
Based on the message on the following page, nrfjprog has been deprecated and should no longer be used:
https://www.nordicsemi.com/Products/Development-tools/nRF-Command...
Hi,
I am nrf52dk/nRF52832 (512kB flash) nordic peripheral_lbs sample as a test environment for establishing OTA updates. In my product firmware, I am facing a situation...
