I have downloaded the motion_driver_6.12 for Nordic Thingy 52 as given in the readme.txt file. And I am using Segger Embedded Studio to build and debug the code. But the IDE...
Hi,
I'm working on a project originally based on the light switch example of SDK 1.0.0 and then upgraded to Mesh_SDK 2.0.1 and nRF5_SDK_15.0.0
I use the code shown in...
I am looking for a freelance / contract developer to help us get nRF53840 working as a BLE controller under linux. ie: basic BT linux adapter. Integrated with BlueZ and similar...
Dear all,
I use FDS module to store some data in flash of nRF52832. I modified the example "ble_app_uart" based nRF5_SDK_15.2.0_9412b96 to test the fds functions feature...
Hello,
I am using nrf51422 with stm32L0. There is a uart connection between nrf51422 and stm32l0. I want to transfer data from stm32l0 to nrf51422 through usart and push...
hi........... folks
i am merging two programs together uart and TWI sensor ...using nrf52382 and segger 15.2version
i am getting the error in ble_nus_send ,
even i have...
Hello,
we are using the nRF52840-DK.
File: secure_bootloader_ble_s140_pca10056.emProject
File: ble_app_buttonless_dfu_pca10056_s140.emProject
In short, we are...
Hi,
I have a well working cli environment under linux where i can compile, program and debug a nFR52 demo board.
I have installed RSSI Viewer (1.05) and Bluetooth Low...
We want to deactivate Mesh DFU packets relaying from the App side to avoid messing with the bootloader firmware. Is there any flag we may use for that?
Hi,
I'm trying to use a Bulk IN endpoint (EPIN3) and am running into an issue.
I call the nrf_drv_usbd_ep_is_busy() function to test whether it is safe to proceed with...
Hello
I am using buttons less DFU,
S132_nrf52_6.1.1 softtdevice
using Android + nrf connecct, I can update the device with DFU
using IPhone 6, I can not update...
I am able to provision using BlueZ's meshctl tool on Raspberry Pi3. However, after restarting meshctl, I am not able to control my device. I tried the "connect" command after...
This isn't exactly a question, because after like...8 hours of debugging, I figured it out. However, in zephyr/samples/bluetooth/mesh, it defines a hardcoded device uuid ...
I am using ble_app_blinky_c application for my project. I want to update my central's default MTU size from 23 to 150 and I know my peripheral device supports MTU size of...
hi,
currently i am using maste r(nRF5_SDK_15.3.0_59ac345\examples\ble_centra\ble_app_uart_c) and slave (nRF5_SDK_15.3.0_59ac345\examples\ble_peripheral\ ble_app_uart ) example...
Hi
After migration from SDK 14.0.0 to 15.0.0 our FW crashes during SPI session
We use EasyDMA , so we use SPIM driver directly without wrapper nrf_drv_spi
The crash...
Hi,
The central part of multirole example is not able to connect to peripheral (other board with ble_app_uart peripheral) and error returned is in the on_ble_central function...
We're using LTE to communicate somewhat large data packets over MQTT, and we'd like to build in some robustness in case the link goes down or a publish fails to receive an...
as soon as I built and run my firmware program on SES ARM 4.22, RF connect scanner can find the ble device (NRF52832). But after 10 seconds later, i do rescan in RF Connect...
Hi, I need to activate uart on pca10059 i can't find where pin TX and RX in pca10059. i already read the schematic and try uart example but end up with can't send or receive...
