I am trying to get a good handle on the difference in average power consumption between BLE point to point and Zigbee on an nRF52840. We have battery powered products and...
Hi, For my project, I need to design a BLE packet sniffer which scanning the 40 channels. Therefore, I need 40 dongles are connected to a computer that can read and transfer...
I am writing code to get a nrf52840 DK to associate with an existing 802.15.4 coordinator using the 802.15.4 API module within SDK 15.2.
I've called "mlme_scan_req" and...
Currently, I am able to use Mqtt Publisher or Subscriber with only one Nrf52 device. I can ping to the device with link-local address.
I am using Nrf52832 with SoftDevice...
Hi everyone,
After days of figuring out how CMake works, I try to write a CMakeList.txt myself, and decide to put my progress on this community. Right now, using CLion with...
i am using nrf 52832, i got SAADC example code from sdk. that code done by using timer. i could not understand timer section. Is available SAADC simple example code without...
Hello everyone,
as indicated by this question https://devzone.nordicsemi.com/f/nordic-q-a/35692/adding-nrf52-dk-to-github-mesh-demo-for-thingys/138327#138327 I am trying...
Hi.
I've just received my nRF52840-PDK and now I am trying to run usb examples from SDK 13.1.0.
I have started with VisualGDB using arm-eabi toolchain and USB HID Generic...
Setting interrupt priority according to FreeRTOS documentation is an inverted priority sequencing, i.e. lower number is high priority. However in the freeRTOS example provided...
Hi,
I am seeing an issue where after enabling read back protection (rbp) on NRF52 and using sdk 12.1 the tag goes to state where it drains a lot of current.
command used...
Hello!
I'm using SDK 12.3.0 with nRF51822. Unfortunately since the begining I've got a problem with TWI interface. It keeps crushing my app. For no reason. At the beginning...
Hello,
I am using sdk 12.3.0 and pca10040 board. I want to update the firmware OTA. I am following this post
devzone.nordicsemi.com/.../
I am stuck at step 4)...
I am using the nRF52832 development board, S132 and SDK11.0, I have some questions about Bluetooth pairing,The project under the link：examples\ble_peripheral\ble_app_uart...
when we use twi to transmit data in iic mode ,the nrf52832's power is unacceptable,too high!we read and write data in 50times per second.every time, we transmit 24 byte data...
I JUST NEED TO KNOW NUMBER OF ON PULSES PRESENT IN THE PWM OUTPUT CAN I USE PIN CHANGE INTERRUPT TO COUNT THE NUMBER OF ON PULSES OR SOME OTHER METHOD IS AVAILABLE
Hi,
We need to pass the radio certification and in order to simplify the setup we created an application to setup BLE TX/RX/CC/MC from an NFC command but we meet a strange...
Hello,
As a lot of person, I have a problem for use nrf52832(pca10040 board) with spi as slave.
I check my master with salae probe tool and this part is correct. Chip...
Hello,
my nRF52 Preview dev.kit don't upload the last 2016 march 15 firmware update
from nRFgo app. It gives me always an error and the progress bar stay at 0% value.
...
Hi,
Need you suggestion regarding our use case but first I would like to explain about our use case.
In our use case there be beacons and receiver. Beacon we are considering...
Hi, I am a beginner and trying to understand the SD card example for nrf52 DK. When I change the pins from the given configuration
#define SDC_CS_PIN ARDUINO_10_PIN
#define...
Hello all,
During testing of my nRF51 based device some Android based phones unable to connect or at least connect from the first time. The same device connects perfectly...
