Hi everyone,
After days of figuring out how CMake works, I try to write a CMakeList.txt myself, and decide to put my progress on this community. Right now, using CLion with...
i am using nrf 52832, i got SAADC example code from sdk. that code done by using timer. i could not understand timer section. Is available SAADC simple example code without...
Hello everyone,
as indicated by this question https://devzone.nordicsemi.com/f/nordic-q-a/35692/adding-nrf52-dk-to-github-mesh-demo-for-thingys/138327#138327 I am trying...
This is both a general tip for users and a question; does anyone have good success with the LIS2DH12 double-tap feature? The 3-axis accelerometer works well but the use of...
Hello-
I'm working with the " Experimental: Wireless UART Example".
Is there any way to periodically send data rather than just typing data into terminal?
hi,
I used nRF52932QFAA ,SDK14.2 uart bootloader.it works well with softdevice loader 5.0.0.But when I download my app(without softdevice),it cannot work.
Flash composed...
I just got the board, installed the nRF connect sw. Then installed the J-link, connected the board, power it on and run the quick guide, but it searches and doesn't find anything...
I've been using PPK2 to test our work for maybe around 3 years. it's always been steady and stable and can run for several days without problem. Mostly I'm using the PPK2...
I'm running the nrf5340_audio_dk and using version 2.6.0-rc1. When connecting one NRF5430 as headset to another NRF5340 gateway, running BIS mode everything works fine. But...
Hi,
We've been working on an IoT device that uses an nRF52840 in a pre-approved module from Moko. We are getting ready for a commercial launch in 2026, but I am very confused...
I have noticed that the dts file includes the configuration for arduinio_spi, along with the corresponding pins associated with spi4. However, I am unsure about how to utilize...
The Bluetooth 6.0 Channel Sounding feature supports multi-antenna functionality. The nRF54L15-DK development board is currently single-antenna. Is there any official documentation...
Hello,
I am wondering how I can enable APPROTECT through UICR with a TFM project. Using ncs2.6.0 and nrf5340. My project makes use of TFM to separate secure and non-secure...
Hello,
I am experiencing an issue with the I2S interface on my nRF5340 DK while using the nRF5340 Audio Unicast Server application with the nRF Connect SDK v3.1.0. I am...
Hi,
I'm trying to test onomondo static profile with a custom board build with an nrf9161 chip. So I've followed onomodo readme, I got an error when i'm trying to build...
Hello,
Im worried i bricked my PPK2, as I had it in ammeter mode possibly reverse VIN/VOUT connections to my DUT.
The DUT is powered over usb externally. I tried to measure...
Jeg har en skoleoppgave i teknologi og forskningslære 1 om CPU-en. I denne oppgaven må jeg stille spørsmål til en virksomhet som er involvert med denne teknologien. Derfor...
Hello,
I am trying to set the TX Power on theThingy:53 to -20 for advertising. However when I check the output files, the Option ` CONFIG_BT_CTLR_TX_PWR_MINUS_20 ` is always...
Hello,
I am planning to use the nRF5340 in High Voltage mode and LDO mode. Currently, I am designing a PCB where minimizing the component count is critical.
I understand...
HI
I previously used the NFC feature in SDK version 3.0.0, which had an abnormal current issue after each trigger. After applying a patch from the forum, this problem was...
I’m designing a PCB using NRF9151-LACA-R7 and an NRF52810-QFAA-QFN48 Our CM needs the exact temperature data for SMT reflow , but we can’t find it clearly in the datasheets...
