Currently, I am able to use Mqtt Publisher or Subscriber with only one Nrf52 device. I can ping to the device with link-local address.
I am using Nrf52832 with SoftDevice...
Hi everyone,
After days of figuring out how CMake works, I try to write a CMakeList.txt myself, and decide to put my progress on this community. Right now, using CLion with...
i am using nrf 52832, i got SAADC example code from sdk. that code done by using timer. i could not understand timer section. Is available SAADC simple example code without...
Hello everyone,
as indicated by this question https://devzone.nordicsemi.com/f/nordic-q-a/35692/adding-nrf52-dk-to-github-mesh-demo-for-thingys/138327#138327 I am trying...
This is both a general tip for users and a question; does anyone have good success with the LIS2DH12 double-tap feature? The 3-axis accelerometer works well but the use of...
Hello-
I'm working with the " Experimental: Wireless UART Example".
Is there any way to periodically send data rather than just typing data into terminal?
Hey Devs,
Would someone be able to tell me the power draw on the Thingy? How long will the onboard battery (1440 mAh) last on it?
Help is appreciated.
Thanks,...
Hi, I am developing firmware to run on a custom board using the nRF52810-CAAA chip. I need to meet very strict lower power consumption thresholds, and need to very precisely...
We are in development of a wearable ecg medical device. We want to add 4g low power capability. The device is a patch worn by patients 24/7 up to 30 days. Our current requirements...
Hi,
Is it possible to set CONFIG_HEAP_MEM_POOL_SIZE to be more than 16384?
I try to configure CONFIG_HEAP_MEM_POOL_SIZE = 94208 and when the heap allocated until 36830...
I have a device at -35 °C temperature, and sometimes I get the error "BLE_ERROR_INVALID_CONN_HANDLE" when in the ble_evt BLE_GATTS_EVT_RW_AUTHORIZE_REQUEST. I'm using the...
For pairing key passing in ble_app_hrs, i have used the ble_app_gls example but it did not worked.
can anyone help me in how to pass pairing key issuse.
i have a question...
Hi! I am developing a network of temperature and humidity sensors, using nrf52832 and hts221 with the ide ses ... for this, I am using thingy 52 as a peripheral that sends...
Hi,
I have a project with NRF52832 and PCA10040 and SDK 16 and need to use both BLE and UART DFU. I can initialize and use them separately but I don't know how to use them...
Looking at the GPS driver source code, it seems there is no GPS hot start mode. In order to get the hot start working, do I have to modify the driver myself, or is there some...
have installed the software for Wireshark and I can see the interface in Wirshark, but I do not see and COM appearing in the Interface window nor does the sniffer appear as...
After many reboots, suddenly I got stuck at this error on every boot:
The data that's on the flash pages:
My mesh init params:
Using NRF52832, SDK 15.3.0, SD 132...
I have designed my own board, based around the nRF9160 but unfortunately I am unable to connect to an LTE network.
I am running the at_client code and using LTE Link Monitor...
Hello guys I am using nrf52840 interfacing analog sensors like potentiometer and accelerometer. This is not related to nrf, but I want to design a simple ADC filter that I...
Using a clean mesh sdk 3.2.0, I created a build directory inside the folder where I extracted the mesh sdk to.
Then, inside that directory, I used CMAKE with the following...
Hello,
I am currently developing a product using the nRF9160. I would like to use concurrently GPS and LTE-M.
I send periodically data to my server using LTE-M network...
