hi........... folks
i am merging two programs together uart and TWI sensor ...using nrf52382 and segger 15.2version
i am getting the error in ble_nus_send ,
even i have...
Software and Softdevice: SDK 12.3.0 keil5
Platform: Windows 10
Hardware: NRF52832 DK
I am trying to combine WDT and FATfs together. But once I have both of them, there...
I am trying to get a good handle on the difference in average power consumption between BLE point to point and Zigbee on an nRF52840. We have battery powered products and...
Hi, For my project, I need to design a BLE packet sniffer which scanning the 40 channels. Therefore, I need 40 dongles are connected to a computer that can read and transfer...
I am writing code to get a nrf52840 DK to associate with an existing 802.15.4 coordinator using the 802.15.4 API module within SDK 15.2.
I've called "mlme_scan_req" and...
Currently, I am able to use Mqtt Publisher or Subscriber with only one Nrf52 device. I can ping to the device with link-local address.
I am using Nrf52832 with SoftDevice...
Hi everyone,
After days of figuring out how CMake works, I try to write a CMakeList.txt myself, and decide to put my progress on this community. Right now, using CLion with...
Hello,
I am currently writing a script whose purpose is to automatically provision and configure devices.
My question is related to the devkey_handle and address_handle...
With SDK 14.2.0 and S332 softdevice, I'm using UART to control ESP8266 WiFi module with AT commands and I'd like to replace app_uart (+FIFO) with nrf_serial , in order to...
Hi,
I am setting OOB with sd_ble_gap_auth_key_reply() method { 0x11, 0x11, etc 16 bytes }, but when trying to connect with desktop nRF Connect there is an error 132 inside...
Hi,
I am getting errors when attempting to include the nvs library to save data to flash storage on the nRF9160 DK. My CMakeLists.txt:
I get the same errors with or...
Hi,
We tried to use a smartSIM from Sierra Wireless with the nrf9160DK without success.
The nrf91 can connect to the LTE network after a few minutes (LED4 steady). However...
Hi,
I did have a working development board. I was working to disable serial and disable as much as possible to get the power usage down. It seemed to be working (although...
I tried this using the ram_retention example from the SDK (nRF5_SDK_15.3.0). The example (Ram Retention) still seems to work if the lines concerning NRF_POWER->RAMON and NRF_POWER...
Hi,
our appliction need to using I2S worked at 96kHz sampling, and i find two parameters , MCK and the CONFIG.RATIO,but when i use this formulation:
LRCK = MCK /CONFIG...
Hello,
I think about connecting two central devices (nRF's 52840) using one common antenna. One device will be only RX and will scan for a advertisements, second will manage...
Hi, I am from China. My company made a BLE module with chip nRF52810. Recently , I coded a program for it by SDK12, based on ble_app_uart example. I modified the corresponding...
I have setup the nRF52840 DK as below
https://devzone.nordicsemi.com/nordic/nordic-blog/b/blog/posts/how-to-setup-the-thread-demo-displayed-live-at-google-i-o
Setup WireShark...
Hi,
We are currently going to try and implement FOTA/DFU with an nRF52840 controller and an nrf52832 peripheral. Is there any example for how this can be accomplished...
Hi,
I currently have a nRF52840DK pre-programmed with the DFU over BLE, but with the debug version. I am unable to physically get to the device, if I wish to perform a...
Hello,
We are using the SPIS on the nRF52832. We are seeing a higher than expected consumption when it's enabled and not used.
I measure around 7uA extra when enabling...
