I have downloaded the motion_driver_6.12 for Nordic Thingy 52 as given in the readme.txt file. And I am using Segger Embedded Studio to build and debug the code. But the IDE...
Hi,
I'm working on a project originally based on the light switch example of SDK 1.0.0 and then upgraded to Mesh_SDK 2.0.1 and nRF5_SDK_15.0.0
I use the code shown in...
I am looking for a freelance / contract developer to help us get nRF53840 working as a BLE controller under linux. ie: basic BT linux adapter. Integrated with BlueZ and similar...
Dear all,
I use FDS module to store some data in flash of nRF52832. I modified the example "ble_app_uart" based nRF5_SDK_15.2.0_9412b96 to test the fds functions feature...
Hello,
I am using nrf51422 with stm32L0. There is a uart connection between nrf51422 and stm32l0. I want to transfer data from stm32l0 to nrf51422 through usart and push...
hi........... folks
i am merging two programs together uart and TWI sensor ...using nrf52382 and segger 15.2version
i am getting the error in ble_nus_send ,
even i have...
Is it possible for a nrf51822 running s130 to advertise and scan at the same time?
I am trying to scan for other BLE devices using s130 softdevice, but cannot find an example...
Hi,
I have learned that you can change the MAC address on a device by using sd_ble_gap_address_set. However, when I press the sw2 button on the beacon (running a modified...
While reading about setting up nRF51 development environment on OS X , I came across the following:
Unfortunately the only way to erase
the memory is to do some magic...
Hello everyone,
I am trying to communicate among 2 NRF24L01+ modules using 2 ATmega16A microcontrollers.
My SPI communication is working fine as I am able to write and...
I've tried to set up my own BLE project as an exercise in understanding what's going on. It's going okay, with the exception that the device isn't advertising the data that...
I write PWR_UP using SPI and then read the Reg <0>. but I am not getting what I wrote.
Step 1 : Power ON using 3V.
Step 2 : Delay for 1 Sec to get into POWER DOWN MODE...
Hello,
On my custom board, I'm receiving chunks of UART data, without flow control, at 115200bps. Sometimes (its quite frequent now... sometimes after 10 chunks, sometimes...
I'm working on a PC application (using nrf51-ble-driver_win_0.4.1 API) to connect a BLE device and discover BLE services.
Today, I'm tying to connect the Nordic dev kit...
When discovering services using nrf51-ble-driver_win_0.4.1 driver, some ID are received with type BLE_UUID_TYPE_UNKNOWN. So I assume they are 128bits. I then retrieve the...
I downloaded the BLE beacon app S110 v7.1.0 to a nRF51-DK board. The current measurement pins were attached to a 10 Ohm resistor.
I observed the AC-coupled voltage at one...
Hi. We've got a chip with a code QFACA10. I am trying to find out if there is the internal pull-down of SWD line or not. It seemed that adding an external pull-down had positive...
Hi all,
I want to know the effect on power consumption of pins input buffer on and off, does there are big differences between them?
Another question is, since there...
Hey everyone,
when i was trying to compile i got this error which says
._build\ble_app_bci.axf: Error: L6200E: Symbol SWI0_IRQHandler multiply defined (by nrf_notification_manager...
i have few question based on nordic i am using N51822.
1: does device goto sleep, while testing i see sometimes device gets automatically disconnected.
how can i solve...
