I have a PCB with an nRf51822 @1.8V, using the SDK 10 (no chance to change it).
The PCB itself with everything but the nRF (we did not iron it on purpose to measure consumption...
I have downloaded the motion_driver_6.12 for Nordic Thingy 52 as given in the readme.txt file. And I am using Segger Embedded Studio to build and debug the code. But the IDE...
Hi,
I'm working on a project originally based on the light switch example of SDK 1.0.0 and then upgraded to Mesh_SDK 2.0.1 and nRF5_SDK_15.0.0
I use the code shown in...
I am looking for a freelance / contract developer to help us get nRF53840 working as a BLE controller under linux. ie: basic BT linux adapter. Integrated with BlueZ and similar...
Dear all,
I use FDS module to store some data in flash of nRF52832. I modified the example "ble_app_uart" based nRF5_SDK_15.2.0_9412b96 to test the fds functions feature...
Hello,
I am using nrf51422 with stm32L0. There is a uart connection between nrf51422 and stm32l0. I want to transfer data from stm32l0 to nrf51422 through usart and push...
Hi,
Here is output of my chip and i want to read it but there is a problem 25 uS low width (T) is to quick for nRF51822
Can you give me some tips, how to read this 3 signal...
Hello all,
I notice that this library isn't listed in the "SDK Common Libraries" for S210 - is it ok to use this? Internally it does seem to be ANT-aware, even though softdevice_handler_init...
Hi everyone,
I'm using NRF51822 controller for an application, to store 2 float variables in the memory using persistent storage manager feature.
However, when I try...
Hi All,
I try to implement the DFU funtion in my module, but the message return is “Not Supported”.
Please suggest me, how could I do about it?
Thanks.
Vic
...
Hello,
Is there a restriction that I cannot have same address LSByte for radio pipes?
It seems that i am failing to receive data on pipe 0 if for example I have pipe 0...
Hi:
I use SDK7.2.0 encountered a problem when I was disconnected, has reached the maximum number of bonding, I want to remove the first bonding information. I do not know...
when i use sd_ble_gatts_hvx() to send data,it cause a HardFault error。 when i trace the sd_ble_gatts_hvx() function,it will run to 0x00016432,in there will be compare two...
Hi,
I use sd_ble_gattc_write function to write to my peripheral with my central device. I'm sure the settings should be right but i still can't see any change on peripheral...
hi,
i have successfully entered the dfu mode many times and could change the applications and reenter the DFU mode.
But then i tried loading the softdevice at "nRF51_SDK_8...
Hi, All,
I am currently developing with nRF51822AC. Due to some issue, we would like to replace the current 16MHz crystal with a crystal other than this frequency. We would...
softdevice 8.01 s110
device nrf81522
hts example,add three ch adc,lcd eg.
phone : HTC one M7
app:nrf tools HTM
when try to connect the device by BLE, when recive the...
Hello!
I am trying to run example uart project (uart_pca10028) on PCA10028 development board. When code is loaded to the microcontroller it signalizes error - all leds...
Hello All,
I am working with a pre-programed PCB; the main components of the are a nRF51822 chip, a GPS, and a GSM. I am using a J-link to communicate to the entire board...
Hi,
I have a BLE thermometer I want to snif using nRF-Sniffer and Wireshark.
Unfortunately I'm unable to sniff the data, I only see the initial "hand-shake".
Process...
