Hi,
I'm working on a project originally based on the light switch example of SDK 1.0.0 and then upgraded to Mesh_SDK 2.0.1 and nRF5_SDK_15.0.0
I use the code shown in...
I am looking for a freelance / contract developer to help us get nRF53840 working as a BLE controller under linux. ie: basic BT linux adapter. Integrated with BlueZ and similar...
Dear all,
I use FDS module to store some data in flash of nRF52832. I modified the example "ble_app_uart" based nRF5_SDK_15.2.0_9412b96 to test the fds functions feature...
Hello,
I am using nrf51422 with stm32L0. There is a uart connection between nrf51422 and stm32l0. I want to transfer data from stm32l0 to nrf51422 through usart and push...
hi........... folks
i am merging two programs together uart and TWI sensor ...using nrf52382 and segger 15.2version
i am getting the error in ble_nus_send ,
even i have...
Software and Softdevice: SDK 12.3.0 keil5
Platform: Windows 10
Hardware: NRF52832 DK
I am trying to combine WDT and FATfs together. But once I have both of them, there...
I am trying to get a good handle on the difference in average power consumption between BLE point to point and Zigbee on an nRF52840. We have battery powered products and...
hi ,
Now, My program it have a crash when i to service discovery.
That always stop at when ble try to get the "PrimaryService(0x1801)" Characteristics
but i not found the...
Hi,
i have only little experience in programming a nRF51, but i want to make just a simple application.
before i used a btm222 BT2.1 SPP module to transmit serial UART-data...
Hi,
i have only little experience in programming a nRF51, but i want to make just a simple application.
before i used a btm222 BT2.1 SPP module to transmit serial UART-data...
Dear Nordic Support Team,
I am trying to write some information in the flash memory without success. In the ble_flash.h file, it is specified that the pages 0-127 are reserved...
hiii....
1.can any one tell where do we call advertising_start() function if we want to advertise after getting disconnect from a central device.
2.in ble_evt_dispatch...
I`m a newbie at Bluetooth Low Energy and Nordic Chips. I bought a DK for the nRF51822. I would like to set I/O pins over android and iOS application.
1.So what application...
Are there any common solutions to the issue of spi_slave.c using an array as its buffer? I would like to setup a circular FIFO, but I am not sure if there is any way to do...
We are using the S110 as a peripheral that emits data via notifications.
Is it safe for the central to also send characteristic writes while notifications are being emitted...
First of all ,i download the SD7.0 to my device, then i download my app to my device,in this case
my device's curent is 100uA.
First of all ,i download the SD7.0 to my device...
Hello,
i need some informatiorn about the layout of the nRFgo Motherboard. More specific i want to build a board which is connected to the ports P0, P1, P2; therefore i...
I'm trying to implement a burst transfer between to nRF24AP2 devices, but I have serious problems getting it to work.
The burst messages are send on a reverse channel to...
Hi, I need to read an analog signal 100 s/s which takes 68us at 10bit. There is very little computation to be done once read probably about 10us which I can do to the previous...
I am experimenting with calling sd_flash_write with waiting,
if it returns NRF_ERROR_BUSY, just try again, and then return either success fail
void flashWrite( uint8_t...
Hey ho,
I'm new to BLE and Nordic. I'm a student from Germany and i want to realize one simple function with Arduino (RedBear Blend with nRF8001) and Android.
I want my...
Hello,
We've heard that the BLE transmission packet length may be increased beyond the limit of 20 bytes in a future version of the S110 softdevice. Would you let us know...
