I have a USB host capable Android device running CentOS via Linux Deploy and everything is working perfectly except i'm unable to connect to my USB nRF24LU1+ Crazyradio PA...
Hi,
I am using multiperipheral mode in ble_app_hrs using the ble_app_multiperipheral example taking the functions on_connected and on_disconnected while connect and disconnect...
Hi,
I'm using nRF52810 on SDKv14.2 and I have changed the bootloader from 52832 to work for 52810. I could do OTA now. I found that the bootloader there is no timeout when...
Is there a way around the issue where bluetooth communication acting as a pass-though terminates the packet whenever null character is found in the packet.
SDK: nRF5_SDK_12...
Hi,
When creating and adding an characteristic to service, what the meaning and difference between these two variables:
attr_char_value.init_len
attr_char_value.max_len...
Hi all,
I have compiled the ble_app_hids_keyboard example for a nRF52832 on a Laird DVK-BL652 breakout board.
I have a tablet running android 5.1.1 and the nordic nRFConnect...
Hello All,
We are using nrf52840 board interface with wiznet550i.
We try to implement mqtt tls 1.2.we get following errors..
I get certificate verification error -0x2700...
Hello,
I am using the Nordic SDK v1.5.0, the modem firmware is mfw_nrf9160_1.2.3 and the DK for the nRF9160
In our application, we are using AT commands to setup and control...
Hi,
There is a similar case:
High power consumption in sleep mode after using SAADC
But I am using the SAADC driver version 2.0 because the oversampling feature is only...
I have seen multiple posts about the nrf5340 that confuse me. Posts like this one say that the board/chip is not available yet, as of 4 days ago. But after looking through...
Hi,
I am new to the Nordic Semi world, having recently purchased a nRF52840 DK board and a nRF52840 dongle.
I have programmed an Arduino Nano 33 IoT over BLE and when...
We experience a 15-20% rate of dropped advertisements from our nRF52840 device. We have used our own application on our device and the ble_app_att_mtu_throughput application...
I am using an nRF52832 to talk to a Melexis MLX90393 (which supports 400kpbs Fast Mode) via the TWIM interface. I am using the TWI Manager library to schedule transactions...
See the below stack trace using nRF5 SDK 17.0.2, where execution had stopped while entering a critical region during an interrupt event when another log was being processed...
Hello,
I am developing a BLE peripheral with three services:
Device Information Service
Custom service #1 with two characteristics
Custom service #2 with one characteristcs...
When i enable BLE_DFU_SUPPORT_ENABLED 1 and debug i have problem Mesh error 4 at 0x00000000 (:0). I'm using sdk: 17.0.2, sdk_for_mesh: 5.0.0. Board nRF52840 DK. Thanks you...
Hello!
I am sending MQTT commands over UART from an NRF52840 DK to the NRF9160 DK which has the ibasis sim card inside. I noticed 3 times so far that after 24 hours , 1...
Hi
I could test Bluetooth Mesh Chat sample on nRF52833-DK nodes. I would like to know whether there is any way to send chat message from nRF Mesh app (non-mesh BLE device...
Hello,
I need to send and receive UDP packets using nRF9160DK via NB-IoT network. I'm able to achieve this using Serial LTE modem . However I need to write my own application...
Hello,
In a design we plan to have 2 x SPI, 1 x QSPI and 1 x I2C interface. For the SPI we plan to use one @32MHz and the other @8MHz.
Please confirm there no "instance...
Hi everybody,
we are trying to bring our beacon's consumption as down as possible. We have nRF52832 mounted on our custom PCB with external 32 kHz crystal and DCDC is enabled...
