Hi, For my project, I need to design a BLE packet sniffer which scanning the 40 channels. Therefore, I need 40 dongles are connected to a computer that can read and transfer...
I am writing code to get a nrf52840 DK to associate with an existing 802.15.4 coordinator using the 802.15.4 API module within SDK 15.2.
I've called "mlme_scan_req" and...
Currently, I am able to use Mqtt Publisher or Subscriber with only one Nrf52 device. I can ping to the device with link-local address.
I am using Nrf52832 with SoftDevice...
Hi everyone,
After days of figuring out how CMake works, I try to write a CMakeList.txt myself, and decide to put my progress on this community. Right now, using CLion with...
i am using nrf 52832, i got SAADC example code from sdk. that code done by using timer. i could not understand timer section. Is available SAADC simple example code without...
Hello everyone,
as indicated by this question https://devzone.nordicsemi.com/f/nordic-q-a/35692/adding-nrf52-dk-to-github-mesh-demo-for-thingys/138327#138327 I am trying...
Hello
SDK12.3, nRF51822
I'm trying to interface the ssd1306 the program freezes in function app_twi_perform internal_transaction_cb is not called internal_transaction_in_progress...
With our nRF53832 device we are not using NFC.
For the lowest power usage should I keep them as disabled NFC pins or change them to GPIO pins and drive them to the same...
Hi!
I have a question regarding nRF51822 supply in internal LDO setup. Is decoupling capacitor on pin DEC2 necessary in this supply setup? Looking at schematic in nRF51...
Hi! As far as understood, there are only 2 clock cycles before the Watchdog timer reset occurs. Is there a way to change/set this to a different value? I need to write in...
Hello!
When using the NRF_LOG module along with a JLink, when I connect the probe to the nRF the RTTClient prints out the first lines that were written when the probe was...
i comple the ble_app_proximity in SDK15, Config APP_ADV_DURATION for 10s,after timeout, no BLE_ADV_EVT_IDLE occur in on_adv_evt.
how put the system into sleep mode?
Hi,
how can i merge ble_app_beacon with mesh sdk beaconing example?? I want to advertise sensor data into beacon advertisement packet. all beacons should be formed a mesh...
Hi All,
I am trying to use TWI on NRF52832 using SDK 12.3 + SD132 but without any success.
For some reason, there is no signal coming out on the configured SDA + SCL pins...
Greetings.
I have PCA10056 0.9.3 and have downloaded nRF5_SDK_15.0.0_a53641a. I am trying to run pre-compiled ble_peripheral examples. I have tried ble_app_blinky and ble_app_uart...
I can connect the board to the Pi and ping it with a globally valid IPv6.
When trying to connect with the MQTT broker, however, no package is sent from the Chip to the Pi...
Hi,
I'm having a problem with the use of bonds since I migrated from SDK 13.1 to 15.0. The problem is that the function gscm_local_db_cache_update() in the gatts_cache_manager...
My kit is a nRF52840 PDK, i've installed SDK_14.2.0 and succesfully built and flashed the ble_app_hrs example project, but i'm not able to work as expected with the debugger...
Hello,
I am trying to build the light_switch_provisioner_nrf52832_xxAA_s132_6.0.0 example with my Laird BL652 DVK, I have modified the board to be hardware identical to...
I was running an application we have recently developed and it was connected to my phone when the LED1 started glowing faintly and then the bluetooth connection dropped. After...
