Hi,
I am getting randomly incorrect SOC reported by pmic npm1300. For most days, it reports correct SOC but then all of a sudden it starts to report incorrect SOC even though...
Hi,
I recently found out about the Periodic interval feature on GRTC CC[0] and it seems like it would be quite useful for my application. Most of my code so far uses the...
Hi,
I have integrated Neuton’s “Transport Type Detection” pre-trained model into my firmware, running on a nRF52840dk. For collecting 9-axis IMU data, I’m using the ST X...
I'm trying to implement a fall detection feature on the headset side using the LSM6DSOX IMU sensor. The IMU is configured successfully, but the board halts after the INT1...
I have a ready hogp struct and I'm trying to subscribe to an input notification (I'm connecting to a bluetooth keyboard) and I'm getting error -22. Here's the callback in...
Hello,
I am trying to count pulses on nRF52840 DK's pin for measuring water flow with hall effect sensor. I tried to implement PPI + GPIOTE + TIMER in counter mode, but...
Hi, I am using nrf52840-based custom hardware and have an external flash connected on SPIM3. Till now I was working with my other peripheral connected on different buses and...
1. By the toolchain manager, the sdk connect and zipped toolchain were downloaded.
I used the downloaded SES to compile examples. For others, they can compile successfully...
Hi All,
My one of the old application is based on SDK11 and i found some issue data corruption with FDS module. After reading some post here regarding FDS issues and also...
Hello,
I am trying to evaluate the Channel Selection Algorithms (CSA) 1 and 2. From what I found on here, CSA 2 is enabled by default in SoftDevice stack, could you please...
Hello everyone. I want to create project from stracth for nRF52832. I use nRF52 DK. I couldn't find any tutorial for this. I create new project under nRF5 SDK 16.0 and specified...
I am using BT840F module from Fanstel which is based on nRF52840.
Currently I am having two EV-BT840 (Evaluation kit for BT840). I have modified 'pca10056.h' as per my board...
OS in development environment :Windows10 HARD :(Taiyo Yuden)EBSHSN Series Evaluation Board : Central / Peripherals CPU :(Nordic) nRF52832 / ARMR Cortex-M4F 32 bit processor...
Hello Devzone,
I've been working on a system to set notifications on time ready for transmission.
The client sends a WWR package to my peripheral and I want my peripheral...
Hello,
Currently, I'm trying to flash my custom board that has nRF52832 with an uart application that I integrated buttonless DFU. I'm running into a problem where when...
1.nrf9160 is there an RF calibration parameter at the factory?
2. If there are calibration parameters, does burning mfw_nrf9160_1.2.0.zip firmware affect the calibration...
I have two devices here, So I combined three HEX files and burned them with JLink, and they don't behave the same. One starts the application normally, and one is always in...
I am using a custom board with nRF8001, where I use external interrupt from the RDYN pin to let MCU know BLE has an event. MCU can recognize these events and change the associated...
Hi,
I added the feature of the 'buttonless dfu' to the 'hrs freertos' using the SDK v15.3.0.
After programmed the built image to the EV board PCA10040, it could run normally...
Hi
I have 2 customised board with nrf52832, I wanted to communicate between 2 devices. Like to send commands like turn on/off LED from my one board to on/off LED on my second...
hi
i want to use iic in my project ,and i add iic func to my project refrence project twi_sensor.
the code of iic like this:
I call the api in the main
then...