I've seen other threads about the issue:
- https://devzone.nordicsemi.com/f/nordic-q-a/117267/light-bulb-sample-works-on-nrf52840dk-and-doesn-t-on-nrf52840-dongle
- https...
Here is my script for programming. Does the sequence is OK? or any advice to improve?
nrfjprog --eraseall
nrfjprog --recover --family NRF53 --coprocessor CP_APPLICATION...
Using the peripheral_uart example routine from the NCSv3.0 library with the 54l15 chip.
1. compilation command： west build --build-dir build . --pristine --board nrf54l15dk...
I'm looking into a rare issue on the BBC micro:bit V2 which uses the nRF52833 as its (application) microcontroller. I used to be familiar with some CPUs from the 80s but my...
I have shifted from silicon labs for BLE project. In Si labs we have burn BLE bootloader and BLE application separately. Do i need to do the same here in nrf controller? If...
I am unable to detect any i2c device when connected to the Nordic nRF54L15 DK kit. I have change the voltage from 1.8v to 3.3v and Tried and explore other pins in Port 0 and...
Hi All,
I have to implement an I2C Slave on my nrf52833 BLE project which is currently working (SDK 2.9.2)
I need some confirmation with the following step:
I have...
I have a question related to memory protection and configuration of device in relevance to soft device.
nrf52832, sdk15, soft device S132
Question 1 : How can I be sure...
In datasheet it had been mentioned that in SPIM0,SPIM1,SPIM2 the SPI clock frequency should not exceed more that 8 Mhz. And SPIM3 nothing is mentioned. Can we understand that...
Hi, I tried to use pc-ble-driver-py script to talk to a nRF52840 DK. It works perfectly with the official connectivity app hex file (the one nRF-Connect PC application loads...
I modified the nRF5 SDK 15.1 example program serial to display a message on a physical device. I added a blinky service to the ble_app_template example program and I am able...
Hi, thank you for looking at my post.
I am using Keil V5.25.2.0 with a nRF51422. I am using the soft device "s310_nrf51422_1.0.0-2.alpha_softdevice." My memory regions for...
So, currently I utilize DK's to program and debug both pca10040 and pca10056 utilizing a custom shield that plugs into any of the nRF52 DKs. The programming and the debugging...
I used SDK15 and ble_app_uart_c.
I start a UART timer sending and start a LED timer. There is a probability of app: SOFTDEVICE: ASSERTION FAILED in the process of running...
Hello all,
I'm using the Nordic SDK 14.2 BSP button handler. I have a push, release, and long push event on a single button. These are working as expected -
Except when...
Hi all
I am using the spi0 to storage the data and twi0 to get sensor data . But after I add the file nrf_drv_twi.c and compile , it complies wrong :.
\_build\nrf51422_xxac...
I have problems with disconnecting my Android devices from my BLE peripheral. I don't think this is Nordic-specific, but perhaps someone has an idea?
Disconnecting using...
Hello,
i have a application with two operating states state1: device is in deep sleep state 2: device is running
i wake up the device from deep sleep via gpio interrupt...
Hi
I am integrating your Android DFU library with our mobile app to do FOTA to our Nordic device nRF52832 . We are using SDK 14.2 and doing the firmware update using zip...
I have the nRF51-DK and have installed Python etc. and the nrf_sniffer_2.0.0-beta-1_51296aa.
3 .hex files are in that installer: sniffer_pca10028_51296aa.hex, sniffer_pca10031_51296aa...
Hello,
I'm trying to shutdown my whole system (nRF 52832, SD132, SDK 12.3) after advertisement fast and slow are finished, following the structure of the peripheral BLE_APP_UART...
