Hello,
I have some code running on an NRF52832 using NRF Connect SDK 2.5.1 which initalizes my BLE with a random private resolvable adress so that I can easily reconnect...
Hi,
We are currently in the research and development phase for a new line of IoT devices designed to work over the Matter protocol. After thorough evaluation, we found the...
Hi,
I started the LBS example on the nRF52DK_52832 kit and connected the PPK2 kit to the P22 pins for measuring power consumption. I am not sure if I did something wrong...
Hello forum ,
As i m working in nordic nrf52840 where i have taken adc value of photodiode ,then i have created service and characteristics i will share the image for that...
Hi
I had a device that did not start up - because it was waiting for the 32KHz clock to be stable.
So I tried to change the setting below from 15pF to 5pF and it started...
-> How to transfer data from one thingy52 device to another thingy52 device. If i have 2 thingy52 devices, I'll send data to 1st tingy52 then 1st thingy52 device will send...
We are developing a product based on ble mesh. We are planning to select NRF52832 chip. Currently what is status of ble mesh on this chip. Does nRF open-mesh support this...
Hi everyone,
I am using new mesh released sdk v2.0.0 in that i have successfully run light switch demo using 3 nRF52832 baord. One for provisioner, 2 client, 3- server....
Hello：
From the nrf52832 data sheet can be seen in the crystal pin is the internal input capacitance, in the table (19.4.2 64 MHz crystal oscillator (HFXO))on P109 , has...
Hi,
I am working with the HID keyboard example in the pca10028 development kit and I facing following problem.
I can connect, pair and bod with Android and IOS devices...
Hi,
I'm testing a PCA10056 S140 (nrF 52840 PDK), SDK15.
I want to test long range extension : using ble_app_att_mtu_throughput application sample.
But when I change...
Hey, I see that the nrf52840 has a single i2s peripheral. and the max sample witdh supported is 24bits. Is there any way to get 4 channel 16bit audio? I only need to record...
Hello Team,
We are using nrf52832 device and SDK version 12.2 Softdevice3.1 to program our watch device.
We have iOS & Android native application to communicate and...
Hi,
I'm trying to transmit data at about 500kbps from custom nRF52 board (peripheral, s132 v5, SDK14.0) to a PCA10040 board with a connectivity FW (based on v3.0.1) connected...
hi to all,
i am developing a device with nrf51822 and i have Inadequate ram problem, i know that softdevice required ram determined in runtime, so there is any way to know...
Hi to all,
i am developing a device with NRF51822 SOC, i want implement a peripheral device and deploy in it a service with two characteristic with notify property, i know...
I want to test the demo https://github.com/NordicPlayground/Nordic-Thingy52-mesh-demo that requires Mesh 1.0.1, but I do not seem to find it anywhere. Can someone point me...
Hi, guys! I am working about a project that I need to get data from sensor and send these data through mesh. I referred from link text ,and the example works well. But, I...
I'm looking for a Nordic expert. I have already designed and built a complete PCB based on the Nordic nRF52832, along with the firmware. I need to improve the PCB design,...
On my nRF52 DK, I'm seeing *something* pull down VCC by about 50 mV once every millisecond (1KHz), and I'm trying to identify its source. (This is only important because using...
