Hi, i'm using NRF5191 with DECT.
DECT modem: 1.0.2
App: hello_dect sample
In datasheet I found that NRF9151 support various band: 1,2,4,9,22
and I'm using these value...
Hi there,
on the nRF5340 Audio DK, there is a FT2232H, which provides FTDI_SPI + FTDI_SPI_SEL.
How this can be used, is there any sample for this available?
And how...
Hi
I have some questions about nRF5340 & nPM1300 decoupling cap
nRF5340
1.For pin A3/D2/H11/K1/L5/L11, ref. SCH is 1uF*1 and 0.1uF*5, could we only connect 1uF*1 and...
Hello,
I have a product based on nRF9160 that uses GNSS. The device is a meter, not an asset tracker, so GNSS is not the TOP 1 feature we need.
When the device is installed...
Hello everyone,
I'm curretly working on a new design based on nrf52832, and I'm validating different interfaces. Currently working on SPI, I'm testing it with a W25Q64...
Hi,
I would like to test a websocket connection over NB-IOT with the nRF9151DK. I started with the websocket_client example but I have those warnings and errors at startup...
I have flashed the Blinky sample onto an nRF52840DK.
The power consumption is extremely high.
I am using an PPKII to in source mode. It is connected to the External Supply...
Hi, p0.06 is always high lever when the following codes are executed:
nrf_gpio_cfg_output(6); nrf_gpio_pin_clear(6);
Why?
Softdevice is used in the project.
I have searched through the examples and the documentation (BTW the online document links are broken - the offline documentation is nice however).
From what I can tell...
Hello Everyone.
I am doing a project where I need to do a Bluetooth communication of data. I have two nRF51 DK so the idea is to connect a particular pressure sensor to...
I am trying to create a state machine that will be able to turn the Bluetooth radio on/off and possibly change the mode of the BLE service for power testing. I hope to run...
I have created an instance of time using the standard time function in C. I have also linked it to a counter on a timer so I can track how long the device has been active...
At CES this year (2018) there was a booth showing essentially a roughly 1/4 size Thingy:52. It wasn't actually at the Nordic booth so I'm not sure if it was actually a Nordic...
I think there's a problem with the beacon advertisement sent by Thingy52. I'm seeing the problem in my own PC code and also air sniffer. The advertising data packet looks...
I am using nrf_fstorage_read command to read data from flash. I have defined my start address as 0x68000 and end address as 0x72000.
I erase the memory through nRFgo studio...
Hello,
I've searched around the forum and followed all the advice given in other threads but am still not having any luck.
I've tried running the nRF sniffer on both a...
Hi there. I just got the nRF52840 DK and am trying to get going with it. I have been looking at this getting started page:
https://www.nordicsemi.com/eng/Products/Getting...
Dear lovely people!
Setup: sdk14 / s132 v5 / nrf52832
Just like with the previous SDKs, I tried to make a multilink nus central fw.
The periph device runs my code based...
Hello,
In our application we heavily use the application scheduler. This was done for 2 main reasons:
serialize access to system resources
enable the soft device to...
Good Afternoon,
I'm writing some config data on an empty record the first time I turn on my board and updating that same record every next time I turn on the board.
...
Hi everybody I have a couple of questions regarding power consumption for the nRF 52 DK Rev. 1 (nRF52832). I currently have an application where I sample 12-bit ADC data via...
I'm working on support for several custom characteristics that require long write support. I'm using the nrf_ble_qwr library, and I've noticed what seems to be a discrepancy...
