Hi all,
I recently bought an nrf52840DK, and yesterday I tried to program an external board through the p20 connector on the DK with the SWD pins. I was able to flash the...
Certainly! Here’s a clear, natural English version of your email:
Dear Specialist,
I would like to better understand the two variables used in the SDK for calculating...
Hi, Using NCS 3.0.0 it would appear that the function sntp_simple_helper does not work with SYS_FOREVER_MS as a timeout value.
Problem: When we pass this value as a timeout...
Hi All,
I have a question and slight confusion as referring to couple of links.
Performing KMU provisioning : Here we are highlighting provisioning of private key up...
Hello
I'm trying to use LittleFS with an external SPI flash, but if the SPI flash isn't available yet at boot time, my application hangs for an uncertain amount of time...
Hi, I am currently working on UART sample codes and have 2 nrf5340 Audio DKs . One acts as peripheral and another as Central. i want to modify the central board to connect...
Hi,
I recently checked support of MCUBoot validation and from NSIB for nrf54l15. (sdk 3.0.0 and above)
During this, I enabled Signature algo as ecdsa-p256.
And...
SDK： nRF5_SDK_11.0.0
Softdevice： s132_nrf52_2.0.0_softdevice
chip:nRF52832
In debug mode, I found through the disassembly window that the program stopped every time...
Hi Guys,
I'm currently developing an app using BLE nrf18522 development beacons.
So I just bought 10 and did a test in a big park with the beacon Tx set to -60dBm and...
Hi, the latest version of SDK is 14.x.x, by principle I should be using the latest, except by going through the SDK14 folders I get the impression that it is exclusively for...
Hello,
This is related to using Seger embedded studio on a mac for thingy52.
With all the amazing help from this forum, I am trying to compile and upload FW onto thingy...
Can we send scan response packet with advertising packet in non-connectable mode? I have taken eddystone beacon example given in SDK 12.3.0 and s130. My beacon has to advertise...
Hey guys,
I'm just being very lazy today and I just skimmed the datasheet for <nRF52832_PS_v1.0.pdf> but didn't manage to find if there are any "pin-muxing" limitations...
Yet another app_uart_fifo question.
I'm using SDK 11 with uVision.
It is my expectation that, if using HW flow control and a FIFO to RX, no received characters should be...
I am writing drivers for external ADC and I need to write my own SPIM driver using hal of NRF52 SPIM. However, after trying for a day I am not able to see my waveform in my...
Hi,
I am using ble_app_blinky_c_pca10040_s132 project, but I found it cannot output log, by using NRF_LOG_INFO. I have tried some ways, but it didn't work. I need your help...
Hi,
I'm in the process of porting code from a PCA10000 rev2 board to a custom board, using the ISP130301 integrated MCU (contains a rev3 nrf51822 IC). I'm using nrf51 SDK...
Hello,
I'm using a modified version of the serial example of the SDK 13.0.0 with a PCA10056.
The modification are that i use nrf_serial_read in non-blocking mode (timeout...
I am using SD132 V5 and SDK 14.1
I found the sd_ble_gatts_characteristic_add() is being used in most of the example projects, but I suddenly found the characteristic_add...
I have nRF52 on both central and peripheral. I'm getting the RSSI value on the central by looking at the RSSI field in the ADV_REPORT event. I see the RSSI values has a wide...
