I am trying to get a WiFi project working using the nRF52840DK and nRF7002EK . I use a 3.3V power source that is supplying power to both nRF's in parallel. For the nRF7002EK...
Hi,
I'm developing firmware for the nRF52840 DK using nRF Connect SDK v2.9.2 , and I’m running into a problem that didn’t occur in v2.8.0 .
My project uses Zephyr and...
I am receiving an error when connecting to a custom board by running nrfjprog --reset, any similarly with any other commands that require connection.
I am connecting through...
We have previously used nRF52840 and for the latest iteration of our board design we are updating to use nRF54L15.
We are aware that for nRF52840 we could map any pin to...
Hi,
I faced with an initialization issue of combination two features: MCUMGR and UART_ASYNC_API. I get a crash right after the FW starts. It looks like the SW configuration...
I checked the nrf52832 manual and found that both XC1 and CX2 are analog input pins for the 32Mhz clock pin configuration. The reference design for both uses 32Mhz crystals...
Hello, I need to configure and compile a sample to send an audio stream (mp3) to the I2S interface.
I tried to put together some configuration from other samples but no...
I have analysed the light switch client and server example apps where the light switch is also the privisioner.
They both start and initialise a bit differently although...
Hello,
I used translation software.
I used the function to enable DCDC mode
I used sd_power_dcdc_mode_set ().
I want to use the optimal mode for power supply voltage...
Hello,
i'm using an nRF52832 as a Bluetooth to UART bridge, similar to the APP UART example.
Another controller (Cortex M7) is connected to the UART. I'm using UARTE with...
Hi,
I'm using two sensors with the same device address through I2C.
each sensor is supposed in a specific period of time (not working together), each sensor has a different...
I am writing a mesh beacon application based on Mesh SDK v0.10's beacon and light switching examples.
A very kind Nordic employee has provided an example on how to combine...
I'm having a problem with using all the memory in the nRF52 Thead SDK 0.10.0. Namely, even if I run one of the smallest examples (e.g. aes one from crypto examples) the flash...
I am using softdevice132, sdk 14.0, pca10040 dk,
when i add nus service to the dfu example, it is not working. there were also some warning about iram start address, which...
I just saw the news that Nordic is providing a free Segger Embedded Studio IDE and the sample projects from SDK 14.1 include the Segger project. I downloaded it and the license...
As I understand we have some problems with time sensitive actions while using softdevice with active ble connection. So here's my questions:
Are there some possible...
Hi All,
I am working on pca10040, nrf52832 and s132. I am using ble_app_uart and sd card, where i want to transmit data received over ble to the sd card.
Can you help...
If there an example on how to test the Raspberry PI border router ( infocenter.nordicsemi.com/index.jsp and some nRF52840 Preview DK together with the official Thread commissioning...
Hello,
I have an application which requires the firmware to be updated on the field. In our device the embedded microcontroller Atmel 328 is connected to nRF52832 through...
When programming the bluetooth mesh light control demo example found in the bluetooth mesh SDK, i get this error using J-Link RTT Viewer:
0> <t: 0>, main.c, 116, -----...
As I know, I need to do watchdog feed on bootloader.
but what If watchdog reload value is long enough for DFU?
for example, if DFU via BLE takes 2-3 minutes, generally...
Hi,
I am using IAR embedded workbench IDE - ARM 8.20.1 (full version) to compile the SDK 14.0 blinky_pca10040_s132 -nrf52832_xxaa example. However, I got some errors which...