I've seen other threads about the issue:
- https://devzone.nordicsemi.com/f/nordic-q-a/117267/light-bulb-sample-works-on-nrf52840dk-and-doesn-t-on-nrf52840-dongle
- https...
Here is my script for programming. Does the sequence is OK? or any advice to improve?
nrfjprog --eraseall
nrfjprog --recover --family NRF53 --coprocessor CP_APPLICATION...
Using the peripheral_uart example routine from the NCSv3.0 library with the 54l15 chip.
1. compilation command: west build --build-dir build . --pristine --board nrf54l15dk...
I'm looking into a rare issue on the BBC micro:bit V2 which uses the nRF52833 as its (application) microcontroller. I used to be familiar with some CPUs from the 80s but my...
I have shifted from silicon labs for BLE project. In Si labs we have burn BLE bootloader and BLE application separately. Do i need to do the same here in nrf controller? If...
I am unable to detect any i2c device when connected to the Nordic nRF54L15 DK kit. I have change the voltage from 1.8v to 3.3v and Tried and explore other pins in Port 0 and...
Hi All,
I have to implement an I2C Slave on my nrf52833 BLE project which is currently working (SDK 2.9.2)
I need some confirmation with the following step:
I have...
Hi,
I am using the nrf52 DK (PCA10040) and have a problem with the USB-UART. For some reason I do not see any log messages in the terminal.
I started with the "coap server...
I used SEGGER Embedded Studio to make ble_mesh_v0.9.1-Alpha project, there was an error while executing the flash_area_is_valid function, this problem occurs in the NRF51822...
I'm using the PCA10028, ble_app_hrs_dfu(sdk11).
Only the three screens below were repeated infinitely when I started to upgrade the softdevice through DFU.
And the...
My android version is the Kitkat.
The nRF Toolbox cannot find services when I changed the application of PCA10028 for example from ble_app_hts to ble_app_hrs.
The message...
Hi I am developing an application for sending data over BLE which I have received over SPI from a non - Nordic chip. I am using the ble_app_uart template for this. But data...
My call to sd_ble_gap_ppcp_set is returning NRF_ERROR_INVALID_PARAMETER.
I have the following connection interval settings:
#define MIN_CONN_INTERVAL MSEC_TO_UNITS(500...
I am running SDK12.3 on an nRF52 and the bootloader on my boards has no problem replacing the application through the DFU process. Now I found a mistake in the bootloader...
I am not sure whether there is a small error in a Gazell packet transaction diagram, or if I have an incorrect understanding. From Gazell user guide :
If only the ACK...
Hi,
I am trying to achieve the maximum throughput when using the nRF51822.As far as I know, the minimum connection interval is 7.5ms and the maximum packets per interval...
I'm running the app_uart_c example on a nRF52832 with softdevice 132 installed.
I'm trying to alter it so that the board only searches for peripheral devices upon a button...
First time using the sniffer.
I want to sniff out the communication for a laser tape measuring device (Boosch GLM 50C)
I noticed that I am unable to sniff out anything...
Hello, I now is in a problem.My equipment set up matching binding but after binding equipment connection will connection failure.If it is not binding, it can be the connection...
Hi
We have developed the product where we are using the nrf51822 chip. Because we are using custom made PCB we have to make tunning of antenna for a long range of BLE module...