Hello and thank you for your help
I am working with the 9151 Rev3 and I attempted to update the IMEI with a valid one provided to us by Nordic
But the following error...
I am working with the DWM3001CDK board for Ultrawide band, but would like to use one of the free LEDs on (P0.14, P0.22, P0.05, or P0.04) as a way to show that the 3 AAs powering...
Hi,
The attached code is based on a sample code from NCS v2.9.1 and creates a LittleFS flash disk on external SPI NOR onboard nrf54L15DK. There is a mismatch in the code...
Somehow a program I have running on a nrf52840-DK board will enable protection. This kind of screws up the small application I am testing because it seems to lock out the...
I noticed that the product information of the nRF54L15 series kit supports 4Mbps, but I'm unsure how to verify it. Are there any relevant examples available? I have currently...
Dear Nordic Support Team,
I am experiencing difficulties flashing firmware to my nRF52832 development board using VSCode with west flash , followed by J-Link...
Hi Nordic team,
We're experiencing two issues related to partition handling in Zephyr/NCS and are looking for your guidance
Issue 1: settings_storage is erased after BLE...
Have project setup to read values from ADC and then run fft_process. Then print them out over uart using NRF_LOG_* statements. However after we call the arm fft functions...
Hello, I am using nrf51822 and SDK11, dual bank dfu ble, S130, 2.0.0.
I made dfu zip file and I modify firmware_crc16 value to the wrong one.
And I zip it again.
But...
hai
i am working with nrf51822 and mbed .
in my application i have requested one page in flash for data store using pstorage.
pstorage_module_param_t param;
param...
Hi,
I'm trying to use NFC type 4 tag on nRF52 side (PCA10040) and poll and read it on Embedded Linux using neard [1]. I'm not an expert in NFC area, so I could be wrong in...
I am migrating a project from SDK 12.1.0 to 12.2.0. According to this question the RAM base needs to be defined in ble_stack_init(). The examples that come with SDK 12.2.0...
I followed the Nordic tutorial on wrapping an SDK sample project in a Makefile managed Eclipse project. I used the ble_app_beacon as the project.
Eclipse will build the project...
I have implemented pwm as suggested in the info centre of nordiac semiconducter. But it showing the following error as shown below image.
Please Help if any one is aware...
Hi,
I think that I found bug in nRF Toolbox release 1.3.0.
1)Application flashing stucks on 95%
2)If you click on Abort, application will stuck in aborting phase. ...
Hi,
Currently I'm working on updating some code based op pstorage on the nRF51822 with SDK 10 an SD S110 (v8).
Right know we're not using "blocks". We're using pstorage_update...
Hi All,
Is there any way to extend RTC2 wakeup interval time more than 2s ?
we know that the maximum interval time of RTC2 on LE1 is 2s, i want to keep LE1 power donw to...
When I just test and build with NRF51-DK there are with BSP Package. such as (pca10028).
But When I make a new PCB Board, Do I have to make my own BSP Package (.h header...
Hi. I have a problem with HID keyboard example. Function sd_ble_gatts_hvx returns 0x00003401. I know that it's means BLE_ERROR_GATTS_SYS_ATTR_MISSING. But how and where I...
Hi everyone,
I am using the nRF52832 and I have use the serial bootloader to update the firmware at one of my clients place.
How should it be done and what do I have to...
Hello everyone.
I have both the two boards now. If I draw a PCB myself and want to use the Debug-out port to debug my PCB, what should I do? Which pin should be connected...
