When I was using the device as peripheral, I was wondering when the Softdevice notified BLE_GAP_EVT_SEC_PARAMS_REQUEST and BLE_EVT_SEC_INFO_REQUEST:
1, when peripheral...
hi dear nordic employee:
I tried to build the project ble_app_hrs_c（pca10040） by keil5
but I get an error :
._build\nrf52832_xxaa.sct(7): error: L6236E: No section...
Hi,
I am a bit confused about power consumption when using app_uart_fifo. To save power I put MCU to sleep in between each sent and received byte by using __WFE and __SEV...
Hi! I am building an android app for my project. I am using Proximity , UART and DFU from nrfToolbox app. I have 3 buttons on my home screen dedicated for each of them. I...
Dear Nordic employee:
1、 what do I have?
I have a thingy52 develop kit（nrf52832）
2、what is my purpose?
the quality of thingy52 audio demo is not good（iphone7）...
Hello Nordic,
My development environment:
SDK>> NRF51822_SDK10, SoftDevice>> S130
Example>> ble_app_uart
I am looking forward to your reply!
Thanks.
Best Regards...
Dear friends,
according to "nRFConnect_BLE_User_Guide_v2.0", to set up a local device,i should complete the following steps:
Connect a development kit or dongle to...
Hi,
I am debugging a program running on the FLPR core on the nRF54L15 development board. I need to call a static library (. a file) on the FLPR core. I use the project created...
Hi:
I connected PPK II with nRF52DK.
PPK 2 is connected to the PC via the PPK 2's USB Data Power port.
The led of both are ON.
I see PPK2 in NRF CONNECT FOR DESKTOP...
Hello, I am debugging a program running on the FLPR core on the nRF54L15 development board. I need to call a static library (. a file) on the FLPR core. I use the project...
I am working Exercise #2 in Lesson 1 and the Screen shots and notes about using nRF KConfig GUI do not match what I see. I am using SDK v3.1.1.
The view I see when I open...
My product is very similar to the PCA10056 and uses NRF52840 and Soft Device S140. The firmware uses NRF5 SDK 17.1.x.
I am trying to set up a periodic scanning feature....
Nordic support,
We are experiencing unexpectedly high and noisy power consumption when using PWM with nRF Connect SDK v2.9.2 on a nRF52811-based custom board, which is problematic...
Hello, I am struggling to find resources or up-to-date information on how to implement the above with NRF54DK (specifically Ezurio BL54L15 DK). Reference material I have found...
Heey, I'm currently trying to implement a w2812 on my custom nrf9160 board. For this I want to use my SPi bus to instruct the ws2812 leds. Because I've already implemented...
Hi,
We have a design error of not having not updated a voltage divider circuit when we increased the high voltage line in an earlier iteration. The range of the voltage...
Hello,
We have a small number of returns for our product, where the modem has gotten into some sort of strange state, and almost seems like it is unresponsive, or blocked...
Hello, May you please help me to understand how to enable the correct mode for testing. This what the laboratory request - "RF frequency fixing software and guidelines of...
We would like to drive two ps/2 interfaces via nrf52840 gpio pins (i.e., reading the protocol bit by bit, via gpio interrupts). A trouble is that ps/2 is timing sensitive...
We're using two nrf54:s, one DK (initiator) and one custom PCB with 2x antennas (reflector)
I've tried adjusting the samples so that multiple antenna paths are supported...
Hi
I have some questions regarding the 32 MHz crystal on the nRF54L15:
If my firmware is configured to use external capacitors, will the very first crystal startup...
Hi,
I am developing on nRF54L15-DK BM (bare metal) for another board with a different pinout.
I need to disable the the MCUMGR log that prints to UART TX pin 1. 04....
