I'm trying to debug a randomly occuring Hardfault. In trying to trace down the source I read the CPU registers use the Nordic hardfault_implementation.c which grabs the register...
Dear nordic employee
my purpose is send a data the length is from 150 to 273
when my server device send data by sd_ble_gatts_hvx（the send length is fixed 10 bytes） ...
Dear nordic employee：
The service I want to find is the sound service of the thing52 thingy sound service
I tried to modify the HRT_central_client project to find the...
When I was using the device as peripheral, I was wondering when the Softdevice notified BLE_GAP_EVT_SEC_PARAMS_REQUEST and BLE_EVT_SEC_INFO_REQUEST:
1, when peripheral...
hi dear nordic employee:
I tried to build the project ble_app_hrs_c（pca10040） by keil5
but I get an error :
._build\nrf52832_xxaa.sct(7): error: L6236E: No section...
Hi,
I am a bit confused about power consumption when using app_uart_fifo. To save power I put MCU to sleep in between each sent and received byte by using __WFE and __SEV...
Hi! I am building an android app for my project. I am using Proximity , UART and DFU from nrfToolbox app. I have 3 buttons on my home screen dedicated for each of them. I...
I am trying to write a low level driver for the TWIM system in a nrf52840 and cannot seem to get the hardware to transfer the TX data out of memory. For many reasons, I do...
I am working on project with nrf54l15dk/nrf54l15, and the project runs on cpuapp without utilizing flpr. So, I decided to release the allocated section of flpr on rram_controller...
I'm seeing an issue where nrf91 SLM, running as an AT modem over UART, sometimes chokes on XSEND command and doesn't respond until the host (nrf54) sends another AT command...
i got the following code from here: https://docs.nordicsemi.com/bundle/ncs-3.1.1/page/zephyr/kernel/services/timing/timers.html , and am using version 3.1.1 of the SDK
...
Hello, I am currently trying to use kmu to store a series of derived keys. My current systems derives AES keys and attempts to store it into KMU. As psa_key_derivation_output_key...
Hi,
in ncs3.1.1 peripheral_uart sample after disable the uart init and gpio_config, the nrf54l05 can achieve the low power state,but the avg Idle current was about 5uA,seens...
Hi! I'm currently trying to use waveshare E-Ink display module (waveshare_epaper_gdeh029a1). First of all, I wanted to test out the lvgl by flashing the sample onto nrf52840dk...
Support Ticket Draft: Severe PPP RX Buffer Overflow on nRF5340 Gateway (NCS v2.5.0)
Subject: Persistent net_ppp: Rx buffer doesn't have enough space Errors on nRF5340...
Hi
It's my first experience with nordic. I need to implement nfr 52833 with RFID-RC522 connected by SPI port. Does anyone have an example to start using the SPI port in...
Good afternoon,
We are using an nRF9151 device to send data over LTE-M. Our gateway, located in Sweden, occasionally resets unexpectedly. We suspect that a fatal error...
My task is to implement the below functionality and shared the below code Disable peripherals and GPIOs before sleep and enable back after wakeup
#include <zephyr/kernel...
Hi,
I am using NCS.
I am using SMP service through BLE, and for security reason I would like to have a custom UUID for the BLE service.
UUID is defined in zephyr\include...
I sent a 242-byte data packet, and using the NRF sniffer to capture the packets, I found that this packet was split into (27-byte per packet) for transmission. This caused...
I’ve been setting up an OpenThread network with multiple OT Sleepy End Devices (SEDs) that periodically transmit sensor data to an IPv4-only CoAP server. To enable communication...
Hi everyone, I’m working on a low-power BLE smart tag using nRF54L15 and nPM1300 PMIC. My requirement is:
When no charger is connected → the system should run from the 3...
