hi dear nordic employee:
I tried to build the project ble_app_hrs_c（pca10040） by keil5
but I get an error :
._build\nrf52832_xxaa.sct(7): error: L6236E: No section...
Hi,
I am a bit confused about power consumption when using app_uart_fifo. To save power I put MCU to sleep in between each sent and received byte by using __WFE and __SEV...
Hi! I am building an android app for my project. I am using Proximity , UART and DFU from nrfToolbox app. I have 3 buttons on my home screen dedicated for each of them. I...
Dear Nordic employee:
1、 what do I have?
I have a thingy52 develop kit（nrf52832）
2、what is my purpose?
the quality of thingy52 audio demo is not good（iphone7）...
Hello Nordic,
My development environment:
SDK>> NRF51822_SDK10, SoftDevice>> S130
Example>> ble_app_uart
I am looking forward to your reply!
Thanks.
Best Regards...
Dear friends,
according to "nRFConnect_BLE_User_Guide_v2.0", to set up a local device,i should complete the following steps:
Connect a development kit or dongle to...
Hi
I have add some function call like sd_ble_enable in mesh example, I test to get
then I set the address and all sd_ble_cfg_set is ok
but when I call "sd_ble_enable...
Hello,
I'm using an nrf52dk board and I am trying to get the RSSI value, and it works fine with the nrfconnect app, except that the the transfer doesn't start at the first...
Hello guys,
I want to work with NRF Mesh but I need help with answering some general questions:
1. Is the current version of the SDK ("nrf5_SDK_for_Mesh_v5.0.0_src") power...
HI,
In my custom board of nRF52805 , I am able to program basic UART application. chip is also generating internal voltages on DEC1 & DEC2 lines.
But i am not able to...
Hi,
I would like to include the direct test mode in my default application that runs the BLE stack. Is this possible ? Ideally I am implementing a custom NUS like service...
Hello,
I wish to download my source code to nRF5340 DK board.
I am working on Ubuntu, SEGGER Embedded Studio for ARM Release 5.50d, ncs 1.6.99 version.
After compile...
I'm trying to restrict the policy used to ensure that the AWS FOTA sample is working. The "allow everything" policy that is stated that it can be used for test purposes seems...
SoftDevice: s140_nrf52_7.2.0_softdevice SDK: nRF5_SDK_17.0.2_d674dde Problem: We trying to use the Secure DFU buttonless feature on our custom board. Our custom board has...
Hello,
We are currently using softdevice version 7.0.1 and SDK version 16.0.0. We are having difficulty nailing down a rare hard faulting bug. Very rarely, the device will...
Hi, I'm using Segger Embedded Studio for developing farmware of nRF52840.
and, using
nrf5_SDK_for_Mesh_v4.2.0_src
nRF5_SDK_16.0.0_98a08e2
I would like to use "es_battery_voltage...
i wish to change P0.13 as tx, P0.15 as rx , P0.17 as ctx , P0.20 as rtx
I change in bsp definitions and it worked for uart peripheral example,
I also change pin...
Hello,
The USB connector came apart from the nRF9160 development kit soon after a purchase was made from Symmetry Electronics. Would it be possible to have the board replaced...
I have an RTOS application into which I integrated a custom BLE service code. Question is, there isn't any need for a separate thread for handling BLE stuff? I see BLE events...
Hi,
I am trying to use UART APIs in blocking mode to receive data from another controller.
I intend to have a timeout on receiving function so not to stuck if no byte...
