hi dear nordic employee:
I tried to build the project ble_app_hrs_c（pca10040） by keil5
but I get an error :
._build\nrf52832_xxaa.sct(7): error: L6236E: No section...
Hi,
I am a bit confused about power consumption when using app_uart_fifo. To save power I put MCU to sleep in between each sent and received byte by using __WFE and __SEV...
Hi! I am building an android app for my project. I am using Proximity , UART and DFU from nrfToolbox app. I have 3 buttons on my home screen dedicated for each of them. I...
Dear Nordic employee:
1、 what do I have?
I have a thingy52 develop kit（nrf52832）
2、what is my purpose?
the quality of thingy52 audio demo is not good（iphone7）...
Hello Nordic,
My development environment:
SDK>> NRF51822_SDK10, SoftDevice>> S130
Example>> ble_app_uart
I am looking forward to your reply!
Thanks.
Best Regards...
Dear friends,
according to "nRFConnect_BLE_User_Guide_v2.0", to set up a local device,i should complete the following steps:
Connect a development kit or dongle to...
Hi
I have add some function call like sd_ble_enable in mesh example, I test to get
then I set the address and all sd_ble_cfg_set is ok
but when I call "sd_ble_enable...
Hi,
I have a peripheral, that should connect to a central automatically. The problem is, there might be multiple
centrals with the same target name available and the central...
Hello, I made a new project at SEGGER for nRF5340 and in the first step before do any development I face with the attached error! The file it asked doesn´t exist !! Could...
Hello DevZone support team!
We are right now doing GCF certification of a device based on nRF9160 and need some urgent support from You!!
Attached is an excel sheet with...
Hi, I need more information about the GPS Chipset used in NRF9160 SIP or give me the name of this GPS module, so I can find its spec on the internet. Thanks in advance
I'm trying to activate because I want to use the HKDF of the nrf_oberon library. But when I try to compile with CMake and the target zephyr_final I get the following error...
Hello,
I am currently trying to program the nRF52832 to be able to receive data from a heart rate sensor. The sensor uses I2C communication and has an additional two pins...
Hi,
I am using this SDK: nRF5_SDK_15.2.0_9412b96 with NRF52840.
Having a disconnection issue where the device disconnects after one hour, If there is more devices connected...
Supposing that I broke off the nRF current measurement pin connector on the nRF9160dk - what are my options i.e. are there other pins that can be made available for the purposes...
Hi support team,
i'm using nrf dongle 52840 to update firmware for orther device, but somethime i can not able to access to send some command until hard disconnect from...
Hi,
I want to connect to Google Cloud IoT and for that I would like to generate the needed credentials on the nRF9160.
I need these ones , but the private key should...
Hi,
We have a strange issue. We have got two nrf52840DK(PCA10056, 2.0.0, 2019.47). The nrf52840DK board is not getting powered up after the board rested in off for a long...
I am following example in https://docs.edgeimpulse.com/docs/nordic-semi-nrf5340-dk but I cannot connect nrf5340 to EdgeImpulse studio . When I connect device via usb cabel...
Hi,
We are developing an IoT sensor application using nRF52832 dev kit as a starting point. We have a sensor that we need to read once every second for 10 milliseconds...
I am using the simple code below to generate a signal from a memory buffer. I cannot generate a signal cyclically. If ONE sequence is used, then the buffer is played once...
